No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, monitoring interface, OPS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing Stack Cables and Powering On the Switch

Installing Stack Cables and Powering On the Switch

Preparing for Installation

Ensure that the following components and tools are available before the installation:
  • Components: copper cables, optical modules and fibers, or active optical cables (AOCs) (For the stack cables applicable to different devices, see Stack Support and Version Requirements.)
  • Tools: ESD wrist strap or ESD gloves

Precautions

When installing or removing optical fibers, do not look into optical ports or connectors without eye protection.
  • Wear an ESD wrist strap or ESD gloves during the installation.
  • Prevent the cables or optical fibers from being twisted.
  • Install or remove optical fibers carefully to avoid damages to fiber connectors.
  • The bend radius of optical fibers or cables must be larger than the minimum bend radius. The minimum bend radius of SFP+ cables is 25 mm; the minimum bend radius of AOC cables is 30 mm; the bend radius of optical fibers is generally greater than or equal to 40 mm.
  • If the fiber connector is dirty, use an alcohol swab or a piece of air-laid paper to gently wipe the fiber connector in one direction.
  • To remove a cable, gently push the connector of the cable and then pull out the cable by the pull ring.

Installation Procedure

Stack member switches can form a chain or ring topology through service port connections. Figure 3-35 and Figure 3-36 shows stack cable connections in a stack that is set up by three S5720-28X-LI-AC switches. On the member switches, the first two 10GE optical ports are configured as stack member ports of logical stack port 1, and the last 10GE optical ports are configured as stack member ports of logical stack port 2.

NOTE:
  • Power off the switch before connecting stack cables.
  • Stack member ports of a logical stack port (stack-port n/1) on one switch must be connected to stack member ports of a logical stack port (stack-port m/2) on another switch.
    • Multiple stack member ports can be bundled into a logical stack port to improve stack reliability and bandwidth. The stack will not split as long as one physical link is available between the member switches.
    • If the logical stack ports on two ends (stack-port n/1 on one switch and stack-port m/2 on the other) both contain multiple stack member ports, the stack member ports can be connected in any sequence.
  • If there are more than two member switches, use the ring topology to improve system reliability. The stack bandwidth is the minimum bandwidth among all stack ports.
  • If there are only two member switches, you are advised to create only one logical stack port on each member switch. The logical stack port can contain multiple stack member ports.
Figure 3-35  Ring topology of a stack set up through service port connections

Figure 3-36  Chain topology of a stack set up through service port connections

To ensure that a stack can be set up successfully, you are advised to perform operations in the following sequence (in a chain topology with three switches A, B, and C):
  1. Wear an ESD wrist strap and connect the other end of the strap to the ESD jack on the cabinet.
  2. Use stack cables to connect SwitchA and SwitchB.
  3. Power on SwitchA and then SwitchB.
  4. Check whether SwitchA and SwitchB have set up a stack successfully. (See Checking Whether a Stack Has Been Established Through Service Port Connections.)
  5. Use stack cables to connect SwitchC and SwitchB, and then power on SwitchC.
  6. Check whether SwitchA, SwitchB, and SwitchC have set up a stack successfully. (See Checking Whether a Stack Has Been Established Through Service Port Connections.)
NOTE:

To specify a member switch as the master switch, power on that switch first. Power on the other member switches after that switch has started. In this example, SwitchA becomes the master switch after the stack is set up.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065674

Views: 49772

Downloads: 431

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next