No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, monitoring interface, OPS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Temperature Thresholds for Fan Speed Adjustment

Configuring Temperature Thresholds for Fan Speed Adjustment

Context

The device uses fixed temperature thresholds to increase and decrease the fan speed by default. The fan speed increases when the device temperature exceeds the upper threshold and decreases when the device temperature falls below the lower threshold. To ensure that the device works at a lower temperature, you can set lower fixed temperature thresholds.

Procedure

  1. (Optional) Run display fan speed-adjust threshold minus

    The default temperature thresholds and the adjusted thresholds are displayed

  2. Run system-view

    The system view is displayed.

  3. Run set fan speed-adjust threshold minus threshold-value [ slot slot-id ]

    The temperature thresholds for fan speed adjustment are specified.

    The new thresholds are the default temperature thresholds minus threshold-value. After this command is executed, both the threshold for increasing the fan speed and the threshold for lowering the fan speed are reduced.

    NOTE:

    The following switches do not support this command:

    • S1720GF series
    • S1720GFR series: S1720-28GFR-4P
    • S2720EI series: S2720-12TP-EI, S2720-12TP-PWR-EI, S2720-28TP-EI, S2720-28TP-PWR-EI-L
    • S5720LI series: S5720-12TP-LI-AC, S5720-12TP-PWR-LI-AC, S5720-28P-LI-AC, S5720-28TP-LI-AC, S5720-28TP-PWR-LI-AC, S5720-28X-LI-AC, S5720-28X-LI-DC, and S5720-16X-PWH-LI-AC
    • S5720S-LI series: S5720S-12TP-LI-AC, S5720S-12TP-PWR-LI-AC, S5720S-28P-LI-AC, S5720SV2-28P-LI-AC, S5720S-28TP-PWR-LI-AC, and S5720S-28X-LI-AC
    • S5720S-SI series: S5720S-28P-SI-AC, S5720S-28X-SI-AC, and S5720S-28X-SI-DC
    • S5720I-SI series: S5720I-6X-PWH-SI-AC, S5720I-10X-PWH-SI-AC, S5720I-12X-SI-AC, and S5720I-12X-PWH-SI-DC

    If one of the preceding switches can set up a stack with other switch models that support this command, this switch also supports this command so that this command can be executed and delivered in the stack.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065674

Views: 42334

Downloads: 358

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next