Licensing Requirements and Limitations for Energy-Saving Management

Configuration Guide - Device Management

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, monitoring interface, OPS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.

Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).

Licensing Requirements and Limitations for Energy-Saving Management

Involved Network Elements

Other network elements are not required.

Licensing Requirements

Energy-saving management is a basic feature of a switch and is not under license control.

Version Requirements

Table 9-1 Applicable product models and versions

Product	Product Model	Software Version
S2700	S2700SI	V100R005C01, V100R006(C00&C01&C03&C05)
	S2700EI	V100R005C01, V100R006(C00&C01&C03&C05)
	S2710SI	V100R006(C03&C05)
	S2720EI	V200R006C10, V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00
	S2750EI	V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00
S3700	S3700SI	V100R005C01, V100R006(C00&C01&C03&C05)
	S3700EI	V100R005C01, V100R006(C00&C01&C03&C05)
	S3700HI	V100R006C01, V200R001C00
S5700	S5700LI	V200R001C00, V200R002C00, V200R003(C00&C02&C10), V200R005C00SPC300, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00
	S5700S-LI	V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00
	S5710-C-LI	V200R001C00
	S5710-X-LI	V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00
	S5720LI and S5720S-LI	V200R010C00, V200R011C00, V200R011C10, V200R012(C00&C20), V200R013C00
	S5700SI	V100R005C01, V100R006C00, V200R001C00, V200R002C00, V200R003C00, V200R005C00
	S5720SI and S5720S-SI	V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S5720I-SI	V200R012C00, V200R013C00
	S5700EI	V100R005C01, V100R006(C00&C01), V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00&C01&C02&C03)
	S5710EI	V200R001C00, V200R002C00, V200R003C00, V200R005(C00&C02)
	S5720EI	V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S5700HI	V100R006C01, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00SPC500&C01&C02)
	S5710HI	V200R003C00, V200R005(C00&C02&C03)
	S5720HI	V200R006C00, V200R007(C00&C10), V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S5730HI	V200R012C00, V200R013C00
	S5730SI	V200R011C10, V200R012C00, V200R013C00
	S5730S-EI	V200R011C10, V200R012C00, V200R013C00
S6700	S6700EI	V100R006C00, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00&C01&C02)
	S6720EI	V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S6720S-EI	V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S6720SI and S6720S-SI	V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S6720LI and S6720S-LI	V200R011C00, V200R011C10, V200R012C00, V200R013C00
	S6720HI	V200R012C00, V200R013C00

For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

During device sleeping configuration, if you run the speed { 10 | 100 } command on any awakening port to set the port rate to 10 or 100 Mbit/s or run the loopback internal command on any awakening port to configure the loopback detection mode, the device cannot enter the sleeping state. To enable the device to enter the sleeping state, you need to configure the awakening port on which the speed { 10 | 100 } or loopback internal command has been configured as a non-awakening port or delete the speed { 10 | 100 } or loopback internal command configuration from the awakening port.
When the interval between the sleeping start time and end time is less than 10 minutes, the device will not enter the sleeping state.

Translation

简体中文

Download

Updated: 2021-09-13

Document ID: EDOC1100065674

Downloads: 749

Average rating:

This Document Applies to these Products

Related Version

Digital Signature File

Digital Signature Authentication Mode