No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, monitoring interface, OPS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
S5720HI and S5730HI Service Port Stacking Support

S5720HI and S5730HI Service Port Stacking Support

NOTE:
  • For the cables that can be used as stack cables, see "Cables" in the Hardware Description. Using other cables may cause exceptions in the stack system, for example, frequent error-down events on stack ports.
  • Combo ports cannot function as stack member ports.
  • For stacking-supported service ports, some of them can be used as stack ports, whereas some can be used as ordinary service ports.
  • Since V200R011C10, S5720HI series switches can set up stacks in service port stacking mode using dedicated stack cables. S5730HI series switches of all versions can set up stacks in service port stacking mode using dedicated stack cables.
  • The number of stacked switches is recommended to be 2 to 9.
Table 3-10  Service port stacking support

Device Series

Port Supporting Stacking Stack Cable Rate of a Single Port

Remarks

S5720HI

Four 10GE SFP+ optical ports

  • 1 m, 3 m, and 5 m SFP+ passive high-speed copper cables
  • 10 m SFP+ active high-speed copper cables
  • 3 m and 10 m AOC cables
  • 10GE SFP+ optical module and optical fiber
  • 0.5 m and 1.5 m SFP+ dedicated stack cable (supported in V200R011C10 and later versions)
10 Gbit/s
  • Any models of the S5720HI series can set up a stack.
  • A switch supports a maximum of two logical stack ports, and each logical stack port supports a maximum of eight stack member ports. Each switch can use a maximum of eight service ports as stack member ports.

NOTE:

An S5720HI supports the stacking function since V200R009C00. When a member device in a stack is faulty and fails to restart for three consecutive times, the device attempts to roll back to a version earlier than V200R009C00 for restart. When the device restarts successfully after rolling back to a version earlier than V200R009C00, a multi-active situation may occur because the version earlier than V200R009C00 does not support the stacking function. To prevent this situation, you are advised to delete the system software earlier than V200R009C00 from member devices when using S5720HIs to set up a stack.

Optical ports on a 4-port 10GE interface card

  • 1 m, 3 m, and 5 m SFP+ passive high-speed copper cables
  • 10 m SFP+ active high-speed copper cables
  • 3 m and 10 m AOC cables
  • 10GE SFP+ optical module and optical fiber
10 Gbit/s

S5730HI

Four 10GE SFP+ optical ports

  • 1 m, 3 m, and 5 m SFP+ passive high-speed copper cables
  • 10 m SFP+ active high-speed copper cables
  • 3 m and 10 m AOC cables
  • 10GE SFP+ optical module and optical fiber
  • 0.5 m and 1.5 m SFP+ dedicated stack cable
10 Gbit/s
  • Any models of the S5730HI series can set up a stack.
  • Two types of ports among 10GE SFP+ optical ports, 10GE optical ports on an interface card, 10GE electrical ports on an interface card, and 40GE optical ports on an interface card on an S5730HI can both be configured as stack member ports, but each logical stack port contains only the same type of stack member ports.
  • When 10GE ports are used as stack ports, a switch supports a maximum of two logical stack ports, and each logical stack port supports a maximum of eight stack member ports. Each switch can use a maximum of twelve service ports as stack member ports.

  • When 40GE ports are used as stack ports, a switch supports a maximum of two logical stack ports, and each logical stack port supports a maximum of two stack member ports. Each switch can use a maximum of two service ports as stack member ports.
  • 40GE ports do not support the stacking function after they are split into 10GE ports.

Optical ports on an 8-port 10GE interface card

  • 1 m, 3 m, and 5 m SFP+ passive high-speed copper cables
  • 10 m SFP+ active high-speed copper cables
  • 3 m and 10 m AOC cables
  • 10GE SFP+ optical module and optical fiber
10 Gbit/s

Electrical ports on an 8-port 10GE interface card

Category 6A or higher network cables (If Category 6 cables are used, ensure that the cables meet requirements of TSB-155.)

10 Gbit/s

Optical ports on a 2-port 40GE interface card

  • 1 m, 3 m, and 5 m QSFP+ passive high-speed copper cables
  • QSFP+ optical module (QSFP-40G-SR-BD not supported) and optical fiber
  • 10 m QSFP+ AOC cable
40 Gbit/s
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065674

Views: 43326

Downloads: 366

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next