No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, monitoring interface, OPS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Changing a Stack Member Port

Changing a Stack Member Port

Procedure (Versions Later Than V200R002)

NOTE:

On the S6700EI, S6720EI, and S6720S-EI, every four of XGE interfaces from the left are added to one group. For example, XGE interfaces numbered 1 to 4 can be added to one group, but XGE interfaces numbered 2 to 5 cannot. That is, the number of the last XGE interface in each group must be the multiple of 4. If you configure any interface in each group as a stack member port, configurations on the other three interfaces in the group will be lost and the three interfaces cannot be used as service ports.

For example: if XGE0/0/2 is configured as a stack member port, the other three ports (XGE0/0/1, XGE0/0/3, and XGE0/0/4) in the same group cannot be used as common service ports and must be added to a logical stack port as stack member ports.

  1. Run the system-view command to enter the system view.
  2. Run the interface stack-port member-id/port-id command to enter the logical stack port view.
  3. Run the shutdown interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> command to set the stack member ports to Down.
  4. Run the undo port interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> enable command to remove the stack member ports from the logical stack port and restore them as service ports.
  5. Run the port interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> enable command to add new stack member ports to the logical stack port.
# Change the stack member port XGE0/0/1 in stack-port0/1 to XGE0/0/3.
<HUAWEI> system-view
[HUAWEI] interface stack-port 0/1  
[HUAWEI-stack-port0/1] shutdown interface xgigabitethernet0/0/1
[HUAWEI-stack-port0/1] undo port interface xgigabitethernet0/0/1 enable 
[HUAWEI-stack-port0/1] port interface xgigabitethernet0/0/3 enable 

Procedure (V200R002 and Earlier Versions)

  1. Run the system-view command to enter the system view.
  2. Run the interface stack-port member-id/port-id command to enter the logical stack port view.
  3. Run the undo port member-group interface interface-type interface-number command to remove the stack member port from the logical stack port.
  4. Run the quit command to return to the system view.
  5. Run the undo stack port interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> enable command to restore the stack member ports as service ports.
  6. Run the stack port interface { interface-type interface-number1 [ to interface-type interface-number2 ] } &<1-10> enable command to configure new service ports as stack member ports.
  7. Run the interface stack-port member-id/port-id command to enter the logical stack port view.
  8. Run the port member-group interface interface-type interface-number command to add new service ports to the logical stack port.
# Change the stack member port XGE0/0/1 in stack-port0/1 to XGE0/0/3.
<HUAWEI> system-view
[HUAWEI] interface stack-port 0/1  
[HUAWEI-stack-port0/1] undo port member-group interface xgigabitethernet 0/0/1
[HUAWEI-stack-port0/1] quit  
[HUAWEI] undo stack port interface xgigabitethernet 0/0/1 enable
[HUAWEI] stack port interface xgigabitethernet 0/0/3 enable
[HUAWEI] interface stack-port 0/1  
[HUAWEI-stack-port0/1] port member-group interface xgigabitethernet 0/0/3
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065674

Views: 41983

Downloads: 358

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next