No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, monitoring interface, OPS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Configuring G.8275.1 Message Attributes

(Optional) Configuring G.8275.1 Message Attributes

Context

G.8275.1 devices periodically send or receive G.8275.1 messages to establish the master-slave hierarchy and transmit time information. G.8275.1 messages include Announce messages and Delay messages. Announce messages are used to exchange time synchronization information between G.8275.1 devices and establish the master-slave hierarchy. Delay messages are event messages, which are timestamped when reaching or leaving a G.8275.1 device to measure the link delay.

If a G.8275.1 device requires high-precision clock synchronization and needs to trace the master clock frequency, reduce the interval for sending G.8275.1 messages. However, this consumes more bandwidth resources. If the sending link delay and receiving link delay are different, you can configure correction for sending or receiving G.8275.1 messages to correct the link delay.

Procedure

  • Configure attributes for Announce messages.
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. Run ptp announce-interval announce-interval

      The interval for sending Announce messages on the interface is set to 2announce-interval, in milliseconds.

      The default value of announce-interval is 7, indicating that the interval for sending Announce messages on an interface is 128 ms.

      If announce-interval is set to a small value, G.8275.1 devices frequently exchange G.8275.1 messages, consuming more bandwidth resources. If announce-interval is set to a large value, high-precision clock synchronization cannot be guaranteed; however, clock synchronization accuracy can be guaranteed.

    4. Run ptp announce receipt-timeout timeout-value

      The maximum number of timeouts for receiving Announce messages is set.

      By default, the maximum number of timeouts for receiving Announce messages is 3.

  • Configure attributes for G.8275.1 Delay messages.
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. Run ptp sync-interval sync-interval

      The interval for sending Sync messages is configured on an interface.

      By default, the interval for sending Sync messages is 64 ms.

    4. Run ptp min-delayreq-interval min-delayreq-interval

      The interval for sending DelayReq messages on the interface is set to 2min-delayreq-interval, in milliseconds.

      The default value of min-delayreq-interval is 6, indicating that the interval for sending DelayReq messages on the interface is 64 ms.

    5. Run ptp asymmetry-correction { positive | negative } asymmetry-correction

      The asymmetric correction for sending G.8275.1 event messages is configured on the interface.

      By default, no asymmetric correction for sending G.8275.1 event messages is configured because G.8275.1 devices consider that the sending link delay and receiving link delay are the same.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065674

Views: 49329

Downloads: 426

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next