No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Service

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of IP Service, including IP address, ARP, DHCP, DHCP policy VLAN, DNS, mDNS gateway, mDNS relay, UDP Helper, IP performance optimization, IPv6, DHCPv6, IPv6 DNS, IPv6 over IPv4 tunnel, and IPv4 over IPv6 tunnel.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Dynamic PMTU

Configuring Dynamic PMTU

Context

When the switch functions as an intermediate node, IPv6 PMTU discovery can be enabled. After this function is enabled, if the length of an IPv6 packet is larger than the IPv6 MTU of the outbound interface, the switch discards the packet, and uses the IPv6 PMTU discovery protocol to dynamically negotiate the PMTU with the source node for packet fragmentation.

After the PMTU ages out, the dynamic PMTU is deleted. The PMTU needs to be renegotiated.

NOTE:

When both static and dynamic PMTUs are configured, only static PMTU takes effect. Static PMTU entries never age.

Only the S5720HI, S5730HI, and S6720HI support the IPv6 PMTU discovery function.

Procedure

  1. Run system-view

    The system view is displayed.

  2. (Optional) Configure the IPv6 MTU for an interface.

    1. Run interface interface-type interface-number

      The specified interface view is displayed.

    2. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

      NOTE:

      Only the S5720EI, S5720HI, S5730HI, S6720EI, S6720HI, and S6720S-EI support switching between Layer 2 and Layer 3 modes.

    3. Run ipv6 enable

      The IPv6 function is enabled on the interface.

      By default, the IPv6 function is disabled on an interface.

    4. Run ipv6 mtu mtu

      The MTU of IPv6 packets on an interface is set.

      By default, the MTU of IPv6 packets on an interface is 1500 bytes.

      NOTE:

      The switch supports MTU setting, so packets sent by the protocol stack are fragmented based on the configured MTU. However, packets forwarded by the hardware chip are not fragmented based on the configured MTU. The maximum length of packets that can be forwarded by the hardware chip is 12K bytes.

      After the MTU value is changed, run the shutdown and undo shutdown commands or the restart (interface view) command to restart the interface and allow the changes to take effect.

    5. Run quit

      Return to the system view.

  3. Run ipv6 packet-too-big drop

    The switch is configured to discard packets with the length larger than the IPv6 MTU of the interface, and IPv6 PMTU discovery is enabled.

    By default, the switch properly forwards packets with the length larger than the IPv6 MTU of the outbound interface and IPv6 PMTU discovery is disabled.

  4. Run ipv6 pathmtu age age-time

    The aging time is set for dynamic PMTU entries.

    By default, the aging time of dynamic PMTU entries is 10 minutes.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065678

Views: 26709

Downloads: 191

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next