No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, RMON2, LLDP, Performance Management, iPCA, NQA, Service Diagnosis, Mirroring, Packet Capture, NetStream, sFlow, TWAMP Light, NETCONF, ECA, Intelligent Video O&M, eMDI, and Network Deception.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the Switch to Periodically Report Logs and Alarms to CampusInsight

Configuring the Switch to Periodically Report Logs and Alarms to CampusInsight

Prerequisites

There is a reachable route between a switch and CampusInsight.

Context

To implement intelligent video O&M, the switch establishes a NETCONF connection with CampusInsight and periodically reports collected information to CampusInsight. Therefore, you must configure the switch by enabling the NETCONF function and configuring the IPv4 addresses and port numbers used for communication with CampusInsight.

Procedure

  • Report logs and alarms to CampusInsight through Syslog.

    1. Configure the switch to use SNMP for communication with CampusInsight. For the detailed configuration procedure, seeSNMP Configuration in the S2720, S5700, and S6720 V200R013C00 Configuration Guide - Network Management and Monitoring.
    2. Configure the Syslog protocol to ensure that the switch sends logs and alarms to CampusInsight.
      1. Run the system-view command to enter the system view.
      2. Run the info-center enable command to enable the information center.
      3. Run the info-center loghost source interface-type interface-number command to configure the source interface from which the switch sends logs to CampusInsight.
      4. Run the info-center loghost ip-address command to configure the IP address of CampusInsight for receiving logs.

  • Report logs and alarms to CampusInsight through Telemetry.

    1. Run the system-view command to enter the system view.
    2. Run the netconf command to enable the NETCONF function and enter the NETCONF view.
    3. Run the source ip ip-address [ port port-number ] command to configure the source IPv4 address and port number for the switch to interconnect with CampusInsight.
    4. Run the smi-server command to create and enter SMI view.
    5. Run the server ip-address ip-address [ port port-number ] command to configure the IPv4 address and port number of CampusInsight to interconnect with the switch.
    6. (Optional) Run the keepalive { interval interval | retry-interval retry-interval | retry-number retry-number } * command to configure connection parameters between the switch and CampusInsight.

      By default, the switch and CampusInsight send heartbeat packets to each other at an interval of 5 minutes, the switch reconnects to CampusInsight at an interval of 5 minutes, and the maximum number of reconnection attempts is 0.

    7. (Optional) Run the max-packet-size size command to set the maximum size of packets sent by the switch to report KPI information to CampusInsight.

      By default, the maximum size of packets sent by the switch to report KPI information to CampusInsight is 5 KB.

    8. Run the collect-item syslog { acl | basetrap | dhcp | entitytrap | ifnet | ifpdt | l2ifppi | l3adp | mcast | mpls | nac | poe | sea | srm } enable command to configure the switch to report logs and alarms to the NMS.

      By default, the switch is disabled from reporting logs and alarms to the NMS.

      NOTE:
      When the dhcp parameter is specified to enable the switch is enabled to report DHCP logs to the NMS, run the dhcp snooping packet-flow log enable command to enable the switch to record logs when DHCP packets are exchanged.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065680

Views: 59262

Downloads: 516

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next