No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, RMON2, LLDP, Performance Management, iPCA, NQA, Service Diagnosis, Mirroring, Packet Capture, NetStream, sFlow, TWAMP Light, NETCONF, ECA, Intelligent Video O&M, eMDI, and Network Deception.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring the Performance Management Function

Example for Configuring the Performance Management Function

Networking Requirements

In Figure 4-2, the end-to-end packet loss statistics collection function is configured on SwitchA and SwitchB to analyze packet loss performance of the VPN between SwitchA and SwitchB. SwitchA functions as the measurement control point (MCP) in the statistics collection system to summarize statistics data.

The network maintenance personnel want SwitchA to send the collected statistics to the FTP server for further analysis. SwitchA connects to the FTP server through the network and there are reachable routes between them.

Figure 4-2  Networking for configuring the performance management function

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure Packet Conservation Algorithm for Internet (iPCA) on SwitchA and SwitchB to collect end-to-end packet loss statistics.

  2. Enable the performance statistics collection function, create a performance statistics collection task, and bind the task to instances.

  3. Configure SwitchA to automatically send statistics files to the FTP server.

Procedure

  1. Configure iPCA on SwitchA and SwitchB to collect end-to-end packet loss statistics. SwitchA functions as the MCP in the statistics collection system.

    # See iPCA Configuration to configure iPCA. The configuration of iPCA is not mentioned here.

  2. Enable the performance statistics collection function, create a performance statistics collection task, and bind the task to instances.

    # Enable the performance statistics collection function, create a performance statistics collection task, and bind all the instances in IP flow performance measurement (FPM) of iPCA.

    <HUAWEI> system-view
    [HUAWEI] sysname SwitchA
    [SwitchA] pm
    [SwitchA-pm] statistics enable
    [SwitchA-pm] statistics-task stream
    [SwitchA-pm-statistics-stream] binding instance-type ipfpm all
    

    # Set the performance statistics collection cycle to 5 minutes and the number of performance statistics collection intervals to 2. That is, the system saves collected performance statistics in statistics files every 10 minutes.

    [SwitchA-pm-statistics-stream] statistics-cycle 5
    Warning: All data of the statistics task will be deleted. Continue? [Y/N]:y
    [SwitchA-pm-statistics-stream] record-interval 2
    Warning: All data of the statistics task will be deleted. Continue? [Y/N]:y
    [SwitchA-pm-statistics-stream] quit
    

  3. Configure SwitchA to automatically send statistics files to the FTP server.

    # Create a performance management server process, and specify the type, IP address, user name, password, and file upload directory of the performance management server.

    [SwitchA-pm] pm-server ftpserver
    [SwitchA-pm-server-ftpserver] protocol ftp ip-address 10.1.1.1
    [SwitchA-pm-server-ftpserver] username user1 password pwd123
    [SwitchA-pm-server-ftpserver] path d:/pmdata
    [SwitchA-pm-server-ftpserver] quit
    

    # Configure SwitchA to automatically send statistics files to the FTP server.

    [SwitchA-pm] upload-config req1 server ftpserver
    [SwitchA-pm] statistics-task stream
    [SwitchA-pm-statistics-stream] upload auto req1
    [SwitchA-pm-statistics-stream] return
    

  4. Verify the configuration.

    # Check the configuration of the performance statistics collection task.

    <SwitchA> display pm statistics-task stream
    Task Name                : stream
    Task State               : running
    Record-file Status       : enable
    Threshold Alarm Status   : disable
    Task Cycle               : 5 minutes
    Sample Interval          : 1 minute
    Instance Type            : ipfpm
    Record Interval(cycle)   : 2
    File Format              : text
    File Name Prefix         : stream
    File Transfer Mode       : active
    Current File Name        : stream20140415154000.txt
    

    # Check performance statistics files in the directory d:/pmdata on the FTP server. The operation procedure is not provided here.

Configuration Files

SwitchA configuration file

#
sysname SwitchA
#
pm
 statistics enable
 pm-server ftpserver
  protocol ftp ip-address 10.1.1.1
  username user1 password %^%#XGl-6~|CU>v0KaYG:LCINi0F!m/Q"SM^Pk.HL~z>%^%#
  path d:/pmdata
 upload-config req1 server ftpserver
 statistics-task stream
  statistics-cycle 5
  record-interval 2
  upload auto req1
  binding instance-type ipfpm all
#
return
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065680

Views: 58981

Downloads: 516

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next