No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, RMON2, LLDP, Performance Management, iPCA, NQA, Service Diagnosis, Mirroring, Packet Capture, NetStream, sFlow, TWAMP Light, NETCONF, ECA, Intelligent Video O&M, eMDI, and Network Deception.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for NETCONF

Licensing Requirements and Limitations for NETCONF

Involved Network Elements

Table 13-6  Involved Network Elements
NETCONF mode Network management system
NETCONF over SSH Callhome
  • S5720HI and S6720EI: Huawei Agile Controller-Campus in V300R002C00 or a later version
  • S5720LI, S5720S-LI, S5720SI, S6720SI, and S6720HI: Huawei Agile Controller-Campus in V300R003C00 or a later version
  • Other products: Currently, no NMS is supported.
NETCONF over SSH Third-party NMSs supporting the NETCONF over SSH mode (The version of switch is V200R011C10 or a later version)

Licensing Requirements

NETCONF is a basic feature of a switch and is not under License control.

Version Requirements

Table 13-7  Products and versions supporting NETCONF

Product

Product Model

Software Version

S2700

S2700SI

Not supported

S2700EI

Not supported

S2710SI

Not supported

S2720EI

V200R012C00, V200R013C00

S2750EI

Not supported

S3700

S3700SI, S3700EI

Not supported

S3700HI

Not supported

S5700

S5700LI

Not supported

S5700S-LI

V200R012C00
NOTE:

Among S5700S-LI series switches, only the S5700S-28X-LI-AC and S5700S-52X-LI-AC support NETCONF.

S5710-C-LI

Not supported

S5710-X-LI

V200R012C00

S5700SI

Not supported

S5700EI

Not supported

S5710EI

Not supported

S5720EI

V200R011C10, V200R012C00, V200R013C00

S5720LI, S5720S-LI

V200R012(C00&C20), V200R013C00

S5720SI, S5720S-SI

V200R012C00, V200R013C00
S5720I-SI

V200R012C00, V200R013C00

S5730SI

V200R012C00, V200R013C00

S5730S-EI

V200R012C00, V200R013C00

S5700HI

Not supported

S5710HI

Not supported

S5720HI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5730HI

V200R012C00, V200R013C00

S6700

S6700EI

Not supported

S6720LI, S6720S-LI

V200R012C00, V200R013C00

S6720SI, S6720S-SI

V200R012C00, V200R013C00

S6720EI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720S-EI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720HI

V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • In versions earlier than V200R013C00, after NETCONF is enabled, some functions must be configured on the NMS using NETCONF, but cannot be configured using command lines on the switch. When you configure these functions using command lines on the switch, the following message is displayed:

    Error: This command cannot be executed in netconf status.

    Starting from V200R013C00, these functions can be configured using command lines on the switch, but the following message will be displayed. Continue the configuration after confirming that no conflict will occur.

    Warning: This command may cause confliction in netconf status. Continue? [Y/N]:
  • From the first version that supports NETCONF, after NETCONF is enabled, some functions can be configured on the NMS using NETCONF or using command lines on the switch. When you configure these functions using command lines on the switch, the following message is displayed. Continue the configuration after confirming that no conflict will occur.
    Warning: This command may cause confliction in netconf status. Continue? [Y/N]:
  • After NETCONF is enabled, some functions can be configured using NETCONF or SNMP on the NMS. Before configuring these functions, ensure that no conflict will occur.

  • After NETCONF is enabled, do not modify configuration files (including the new configuration file specified in the Bootload menu during switch restart) on switches or the configurations delivered by the NMS to switches. Otherwise, data in the NETCONF database and configuration files may be inconsistent and configurations may be lost.
  • If an error occurs in the NETCONF process of the switch, detailed error information of the process will be saved in the directory flash:/core_dump.

  • When the delete-config operation is performed on the NMS to clear configurations in the NETCONF database, the switch automatically runs the reset saved-configuration command to clear the next startup configuration file and cancel the configuration file used for next startup.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065680

Views: 53132

Downloads: 504

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next