No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, RMON2, LLDP, Performance Management, iPCA, NQA, Service Diagnosis, Mirroring, Packet Capture, NetStream, sFlow, TWAMP Light, NETCONF, ECA, Intelligent Video O&M, eMDI, and Network Deception.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the Switch to Periodically Report KPI Information to CampusInsight

Configuring the Switch to Periodically Report KPI Information to CampusInsight

Prerequisites

There is a reachable route between a switch and CampusInsight.

Context

To implement intelligent video O&M, the switch establishes a NETCONF connection with CampusInsight and periodically reports collected KPI information to CampusInsight. Therefore, you must configure the switch by enabling the NETCONF function and configuring the IPv4 addresses and port numbers to communication with CampusInsight, and then enable the switch to report collected KPI information to CampusInsight.

Procedure

  1. Configure the switch to interconnect with CampusInsight.

    1. Run the system-view command to enter the system view.
    2. Run the netconf command to enable the NETCONF function and enter the NETCONF view.
    3. Run the source ip ip-address [ port port-number ] command to configure the source IPv4 address and port number for the switch to interconnect with CampusInsight.
    4. Run the smi-server command to create and enter SMI view.
    5. Run the server ip-address ip-address [ port port-number ] command to configure the IPv4 address and port number of CampusInsight to interconnect with the switch.
    6. (Optional) Run the keepalive { interval interval | retry-interval retry-interval | retry-number retry-number } * command to configure connection parameters between the switch and CampusInsight.

      By default, the switch and CampusInsight send heartbeat packets to each other at an interval of 5 minutes, the switch reconnects to CampusInsight at an interval of 5 minutes, and the maximum number of reconnection attempts is 0.

    7. (Optional) Run the max-packet-size size command to set the maximum size of packets sent by the switch to report KPI information to CampusInsight.

      By default, the maximum size of packets sent by the switch to report KPI information to CampusInsight is 5 KB.

  2. Configure services to be maintained using different commands according to your networking requirements.

    • Configure the switch to periodically report KPI information to CampusInsight.
      1. (Optional) Run the report-interval interval command sets the interval at which the switch reports KPI information to CampusInsight.

        By default, the switch reports KPI information to CampusInsight at an interval of 1 minute.

      2. Run the collect-item { device-data | fiber-module | poe | user-data | device-status } enable command to enable the switch to report collected information to CampusInsight.

        By default, the switch does not report any collected information to CampusInsight.

      3. (Optional) Run the collect-item { device-data | fiber-module | poe | user-data | device-status } interval interval command to set the interval at which the switch collects KPI information.

        By default, the switch collects KPI information at an interval of 5 minutes.

        NOTE:

        When the user-data parameter is specified to enable the switch to report traffic statistics collection of wired users to CampusInsight, run the statistic enable command in the AAA domain view to enable traffic statistics collection for users in the domain.

    • Configure the switch to periodically report audio or video data to CampusInsight.
      1. Run the quit command to exit from the SMI view.
      2. Run the quit command to exit from the NETCONF view.
      3. Run the emdi command to enable the eMDI detection function and enter the eMDI view.
      4. Run the quit command to exit from the eMDI view.
      5. Run the sea command to enable the SEA function for users and applications and enter the SEA view.
      6. Run the rtp-media monitor-type { audio | video } * command to configure the type of media streams to be monitored.
      7. (Optional) Run the rtp-media monitor-period period-value command to set the monitoring period of media streams.

        By default, the monitoring period of media streams is 10 seconds.

      8. Run the quit command to exit from the SEA view.
      9. Run the netconf command to enter the NETCONF view.
      10. Run the smi-server command to create and enter SMI view.
      11. Run the collect-item media-quality enable command to enable the switch to periodically report audio or video data to CampusInsight.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065680

Views: 59704

Downloads: 516

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next