No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Network Management and Monitoring

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Network Management and Monitoring, including SNMP, RMON, RMON2, LLDP, Performance Management, iPCA, NQA, Service Diagnosis, Mirroring, Packet Capture, NetStream, sFlow, TWAMP Light, NETCONF, ECA, Intelligent Video O&M, eMDI, and Network Deception.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring eMDI

Configuring eMDI

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run emdi

    The eMDI function is enabled and the eMDI view is displayed.

  3. Configure an eMDI instance.

    To implement the eMDI function, you must configure an eMDI instance and configure the monitored target flow, monitoring interval, lifetime, and alarm threshold for the eMDI instance.

    1. Run emdi instance instance-id

      An eMDI instance is created and the eMDI instance view is displayed.

      By default, no eMDI instance is created.

    2. Configure a target flow to be monitored by the eMDI instance.

      A target flow is the object monitored by an eMDI instance, and can be defined by any combinations of multiple attributes such as protocol type, source IP address, destination IP address, VLAN ID, source port number, destination port number, payload type, and clock rate. When multiple target flows need to be monitored simultaneously, the source and destination IP addresses and the source and destination port numbers must be specified to define the target flows. Specifying more attributes makes the target flow more accurate. Therefore, it is recommended that you specify more attributes to improve precision of monitoring results. An eMDI instance can monitor only one target flow. Multiple eMDI instances cannot monitor the same target flow.

      • When the protocol of the target flow is TCP, run the following command:

        flow ipv4 tcp source source-ip-address destination destination-ip-address { [ vlan vlan-id | source-port source-port-number | destination-port destination-port-number ]* }

      • When the protocol of the target flow is UDP, run the following command:

        flow ipv4 udp source source-ip-address destination destination-ip-address { [ vlan vlan-id | source-port source-port-number | destination-port destination-port-number | pt pt-value | clock-rate clock-rate-value ]* }

    3. (Optional) Run monitor-period period-value

      A monitoring interval is configured for the eMDI instance.

      By default, the monitoring interval of an eMDI instance is 60 seconds.

    4. (Optional) Run end lifetime { seconds seconds | minutes minutes | hours hours | days days }

      The lifetime of the eMDI instance is configured.

      By default, the lifetime of an eMDI instance is 1 hour.

    5. (Optional) Run alarm { rtp-lr | rtp-ser | dplr | uplr } threshold threshold-value

      An alarm threshold is configured for the eMDI instance.

      By default, the alarm threshold for an eMDI instance is 10.

      When an indicator such as the out-of-order packet rate or packet loss rate monitored by an eMDI instance reaches the threshold for three consecutive times, an alarm is reported to the NMS. If the indicator no longer reaches the threshold within the following 60 consecutive monitoring intervals, the alarm is automatically cleared.

  4. Run start

    The eMDI instance is started.

    After an eMDI instance is started, all parameters in the eMDI instance cannot be modified. To modify the parameters, run the stop command to stop the eMDI instance first.

    To stop the eMDI instance before its lifetime expires, run the stop command.

Verifying the Configuration

  • Run the display current-configuration command to check whether the eMDI configuration is correct.
  • Run the display emdi command to check the eMDI specifications, current eMDI configuration, and running status of the eMDI instance.
  • Run the display emdi statistics instance instance-id [ verbose | abnormal ] command to view statistics about the eMDI instance.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100065680

Views: 53109

Downloads: 503

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next