No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VRRP

Licensing Requirements and Limitations for VRRP

Involved Network Elements

Other network elements are required to support VRRP functions.

Licensing Requirements

VRRP is a basic feature of a switch and is not under license control.

Version Requirements

Table 3-5  Products and versions supporting VRRP
Product Product Model Software Version

S2700

S2700SI

Not supported

S2700EI

Not supported

S2710SI

Not supported

S2720EI

V200R011C10, V200R012C00, V200R013C00

S2750EI

Not supported

S3700

S3700SI

Not supported

S3700EI

V100R005C01, V100R006(C00&C01&C03&C05)

S3700HI

V100R006C01, V200R001C00

S5700

S5700LI and S5700S-LI

Not supported

S5720LI and S5720S-LI

V200R010C00, V200R011C00, V200R011C10, V200R012(C00&C20), V200R013C00

S5710-C-LI

Not supported

S5710-X-LI

Not supported

S5700SI

Not supported

S5700EI

V100R005C01, V100R006(C00&C01), V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00&C01&C02&C03)

S5710EI

V200R001C00, V200R002C00, V200R003C00, V200R005(C00&C02)

S5720EI

V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5700HI

V100R006C01, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00SPC500&C01&C02)

S5710HI

V200R003C00, V200R005(C00&C02&C03)

S5720HI

V200R006C00, V200R007(C00&C10), V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5730HI

V200R012C00, V200R013C00

S5720SI and S5720S-SI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5720I-SI

V200R012C00, V200R013C00

S5730SI

V200R011C10, V200R012C00, V200R013C00

S5730S-EI

V200R011C10, V200R012C00, V200R013C00

S6700

S6720LI and S6720S-LI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720SI and S6720S-SI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6700EI

V100R006C00, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00&C01&C02)

S6720EI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720S-EI

V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720HI

V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • In V200R003 and earlier versions, VRRP can be configured only on the VLANIF interface.

    Starting in V200R005, VRRP can be configured on the VLANIF interface and Layer 3 Ethernet interface.

    Starting in V200R009, VRRP can be configured on the VLANIF interface, Layer 3 Ethernet interface, and sub-interface.

  • Starting in V200R010, VRRP6 can be configured on Dot1q termination sub-interfaces or QinQ termination sub-interfaces.
  • Switches of a VRRP group must be configured with the same VRID.
  • VRRP groups must use different virtual IP addresses. The virtual IP address of a VRRP group must be on the same network segment as the IP address of the interface where the VRRP group is configured.
  • If each switch in the VRRP group uses a different VRRP version, VRRP packets may fail to be transmitted. When a VRRPv3-enabled switch and a VRRPv2-enabled switch belong to the same VRRP group, run the vrrp version-3 send-packet-mode { v2-only | v2v3-both } command to configure the switch to send VRRPv2 packets.
  • If both VRRP and static ARP are configured on a VLANIF interface, a Dot1q termination sub-interface, a QinQ termination sub-interface, or an Ethernet interface on a device, an IP address mapped to a static ARP entry cannot be used as a virtual IP address. If a VRRP virtual IP address is an IP address mapped to a static ARP entry on the device, the device generates incorrect host routes, affecting traffic forwarding.
  • The virtual MAC address of a VRRP group cannot be configured as a static or blackhole MAC address.
  • A maximum of 24 VRRP groups can be configured on the S3700EI, and a maximum of 64 VRRP groups can be configured on other models. Starting in V200R003, the set vrrp max-group-number max-group-number command can be used to set the maximum number of allowed VRRP groups.
  • The ARP aging probe packets sent by a VRRP device uses an interface IP address, instead of a virtual IP address, as the source IP address.
Translation
Download
Updated: 2019-04-04

Document ID: EDOC1100065682

Views: 30044

Downloads: 253

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next