No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Basic Concepts of EFM

Basic Concepts of EFM

OAM PDUs

EFM works at the data link layer and uses protocol packets called OAM Protocol Data Units (PDUs). EFM devices periodically exchange OAMPDUs to report the link status, helping network administrators effectively manage networks. Figure 7-2 shows the format of an OAMPDU as well as the common types of OAMPDUs.

Figure 7-2  OAMPDU format

Table 7-1 describes fields in an OAMPDU.

Table 7-1  Fields in an OAMPDU
Field Description

Destination addr

Destination MAC address, which is a slow protocol multicast address 0x0180-C200-0002. Network bridges cannot forward slow protocol packets. EFM OAMPDUs cannot be forwarded over multiple devices, even if OAM is supported or enabled on the devices.

Source addr

Source address, which is a unicast MAC address of a port on the transmit end. If no port MAC address is specified on the transmit end, the bridge MAC address of the transmit end is used.

Type

Slow protocol type that has the fixed value of 0x8809.

Subtype

Subtype of a slow protocol. The value is 0x03, indicating that the slow subprotocol is EFM.

Flags

EFM entity status:
  • Remote Stable

  • Remote Evaluating

  • Local Stable

  • Local Evaluating

  • Critical Event

  • Dying Gasp

  • Link Fault

Code

OAMPDU type:
  • 0X00: Information OAMPDU

  • 0X01: Event Notification OAMPDU

  • 0X04: Loopback Control OAMPDU

Table 7-2 describes OAMPDU types.

Table 7-2  OAMPDU types

OAMPDU Type

Description

Information OAMPDU

  • Used to discover a remote EFM entity, initiate a handshake process, and establish an EFM connection. After the EFM connection is established, both EFM entities periodically exchange Information OAMPDUs to monitor link connectivity.

  • Used to advertise fault information. Upon receiving a critical link event carried in the Flags field of an Information OAMPDU sent by the remote EFM entity, the local EFM entity sends a trap to the NMS.

Event Notification OAMPDU

Used to monitor links. If an errored frame event, errored code period event, or errored frame second event occurs on an interface, the interface sends an Event Notification OAMPDU to notify the remote interface of the event.

Loopback Control OAMPDU

Used to enable or disable the remote loopback function.

Connection Modes

EFM supports two connection modes: active and passive. An EFM connection can only be initiated by an OAM entity working in active mode. An OAM entity working in passive mode waits to receive a connection request from its peer entity. Table 7-3 lists capabilities for processing OAMPDUs in the two connection modes.

Table 7-3  Capabilities for processing OAMPDUs in active and passive modes

Capability

Active Mode

Passive Mode

Initiate a connection request by sending an Information OAMPDU during the discovery process

Supported

Not supported

Respond to a connection request during the discovery process

Supported

Supported

Send Information OAMPDUs

Supported

Supported

Send Event Notification OAMPDUs

Supported

Supported

Send Loopback Control OAMPDUs

Supported

Not supported

Respond to Loopback Control OAMPDUs

Supported (The remote EFM entity must work in active mode.)

Supported

Translation
Download
Updated: 2019-04-04

Document ID: EDOC1100065682

Views: 31255

Downloads: 255

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next