No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - Device Management

S7700 and S9700 V200R013C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Clock Synchronization Modes

Clock Synchronization Modes


Telecommunications services on modern communications networks require that the frequency offset or time difference between devices be within an acceptable range. This requirement must be met using network clock synchronization.

Clock synchronization includes frequency synchronization and phase synchronization.

  • Frequency synchronization

    Frequency synchronization, also called clock synchronization, indicates that signals have the same frequency and a fixed phase difference. That is, signals are sent or received at an average rate. All devices on a communications network operate at the same rate.

  • Phase synchronization

    Phase synchronization, also called time synchronization, indicates that both frequencies and phases of signals are consistent. That is, the phase offset between signals is always 0.

Figure 13-1 illustrates the difference between frequency synchronization and phase synchronization. If Watch A and Watch B show different time but maintain a constant time difference, for example 6 hours, this is called frequency synchronization. If Watch A and Watch B maintain the same time, this is called phase synchronization.

Figure 13-1  Differences between frequency synchronization and phase synchronization

Synchronization Modes

Two clock synchronization modes are available on a communications network: pseudo synchronization and master-slave synchronization.

Pseudo Synchronization

In pseudo synchronization mode, each switching site has its own highly accurate and stable clock. The sites do not synchronize their clocks with each other. A difference may exist in the clock frequency and phase among the clocks of the switching sites. However, small differences generally do not affect service transmission and can be ignored. Pseudo synchronization is often used on communications networks between countries. Caesium clocks are usually used in countries.

Master-Slave Synchronization
In master-slave synchronization mode, a highly accurate master clock is deployed on a network and traced by other sites. Other network elements on the network use the master clock as the reference clock. Each sub-site traces the clock of the upper-level site. In this way, the clock is synchronized to endpoints on the network. Master-slave synchronization is typically used on communications networks inside a country or region. Master-slave synchronization is classified as direct master-slave synchronization or hierarchical master-slave synchronization.
  • Direct master-slave synchronization

    Figure 13-2 shows direct master-slave synchronization. All slave clocks synchronize with the master clock. Direct master-slave synchronization applies to simple networks.
    Figure 13-2  Direct master-slave synchronization
  • Hierarchical master-slave synchronization

    Figure 13-3 shows hierarchical master-slave synchronization. In this mode, the clocks are classified into three stratum: stratum-1 master clock, stratum-2 slave clock, and stratum-3 slave clock. The stratum-2 slave clock synchronizes with the stratum-1 master clock, and the stratum-3 slave clock synchronizes with the stratum-2 slave clock. Hierarchical master-slave synchronization applies to large and complicated networks.
    Figure 13-3  Hierarchical master-slave synchronization

To improve master-slave synchronization reliability, two master clocks can be deployed: one as the active master clock, and the other as the standby master clock. Under normal circumstances, all network elements, including the standby master clock, trace the active master clock. If the active master clock becomes faulty, the standby master clock takes over as the reference clock for the entire network. After the fault is rectified, the original active-standby relationship is resumed.


Synchronous Ethernet is a clock synchronization technology that carries and recovers clock frequency information through physical-layer code streams. Figure 13-4 shows the clock synchronization procedure:
  • In the transmit direction: Device1 traces the high-precision clock (master clock) and injects the clock information into the PHY chip of an Ethernet interface card. The PHY chip carries the clock information in the serial code stream of the Ethernet line to transmit the information to the downstream node.
  • In the receive direction: The PHY chip of the Ethernet interface card on Device2 extracts clock information from the serial code stream of the Ethernet line, and then sends the clock information to the clock daughter card. The clock daughter card selects the most precise clock (or uses the manually or forcibly specified clock) as the reference clock source based on the automatic clock source selection algorithm and sends the clock source to the system phase-locked loop (PLL). After the PLL traces the reference clock source, the PHY chip of the Ethernet interface card transmits the generated high-precision system clock to downstream devices, and other functions (such as the MAC module) of the local device use clock signals.
Figure 13-4  Synchronous Ethernet

Comparisons between synchronous Ethernet and other clock synchronization protocols

Clock Protocol Whether Frequency Synchronization Is Supported Whether Time Synchronization Is Supported Time Synchronization Accuracy Signal Transmission Mode
NTP No Yes Millisecond accuracy Time signals are transmitted using NTP packets.
Synchronous Ethernet Yes No - Clock signals are transmitted using serial data streams at the physical layer, without affecting upper-layer services and CPU performance.
PTP Yes Yes Sub-microsecond accuracy Clock and time signals are transmitted using PTP packets, and higher time accuracy is achieved with the assistance of hardware.
Updated: 2019-04-20

Document ID: EDOC1100065738

Views: 45241

Downloads: 39

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Previous Next