No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Multicast

S7700 and S9700 V200R013C00

This document describes the configurations of IP multicast, including IP multicast basics, IGMP, MLD, IPv4 PIM, IPv6 PIM, MSDP, multicast VPN, layer 3 multicast CAC, IPv4 multicast route management, IPv6 multicast route management, IGMP snooping, MLD snooping, static multicast MAC address, multicast VLAN replication, layer 2 multicast CAC, multicast network management.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring VSI-based IGMP Snooping SSM Mapping

Configuring VSI-based IGMP Snooping SSM Mapping

Pre-configuration Tasks

Enabling IGMP Snooping

Configuration Procedure

Configuring IGMP Snooping Multicast SSM Mapping is mandatory and (Optional) Configuring an SSM Group Policy is optional.

(Optional) Configuring an SSM Group Policy

Context

If a user joins an any-source multicast (ASM) group, configure a source-specific multicast (SSM) group policy in the virtual switching instance (VSI) to add the multicast group address to the SSM group address range.
NOTE:

By default, the access control list (ACL) applied to an SSM group policy denies all multicast groups. To exclude specific group addresses from the SSM group address range, use a rule permit source any rule with deny rules in the ACL.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run vsi vsi-name

    The VSI view is displayed.

  3. Run igmp-snooping ssm-policy basic-acl-number

    An SSM group policy is configured.

    By default, SSM group addresses range from 232.0.0.0 to 232.255.255.255. After you configure an SSM group policy, the multicast groups specified in the SSM policy are treated as SSM groups.

Configuring IGMP Snooping Multicast SSM Mapping

Context

By configuring SSM mapping, you can set up one-to-one mappings between multicast groups and multicast sources.

SSM mapping applies to a VSI only when the IGMP snooping version running in the VSI is V3.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run vsi vsi-name

    The VSI view is displayed.

  3. Run igmp-snooping version 3

    The IGMP snooping version is set to V3.

    The default IGMP snooping version is V2, but this version does not support SSM mapping.

  4. Run igmp-snooping ssm-mapping enable

    SSM mapping is enabled in the VSI.

    By default, SSM mapping is disabled.

  5. Run igmp-snooping ssm-mapping ip-group-address { ip-group-mask | mask-length } ip-source-address

    The mapping between a multicast group address and a multicast source is configured.

Verifying the IGMP Snooping SSM Mapping Configuration

Prerequisites

The SSM mapping configuration is complete.

Procedure

  • Run the display igmp-snooping port-info [ vsi vsi-name [ group-address group-address ] ] [ verbose ] command to check information about IGMP snooping interfaces.
Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100065742

Views: 46366

Downloads: 46

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next