No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Multicast

S7700 and S9700 V200R013C00

This document describes the configurations of IP multicast, including IP multicast basics, IGMP, MLD, IPv4 PIM, IPv6 PIM, MSDP, multicast VPN, layer 3 multicast CAC, IPv4 multicast route management, IPv6 multicast route management, IGMP snooping, MLD snooping, static multicast MAC address, multicast VLAN replication, layer 2 multicast CAC, multicast network management.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Enabling IGMP

Enabling IGMP

Context

IP multicast routing is the prerequisite for all the multicast functions. Enable IP multicast routing before configuring any multicast protocol.

To configure IGMP functions on the switch, first enable IGMP on interfaces connected to group members.

Procedure

  • Enabling IGMP in the public network instance
    1. Run system-view

      The system view is displayed.

    2. (Optional) Run set multicast forwarding-table super-mode

      The high-specification mode is configured for multicast forwarding.

      In large-scale multicast applications, the switch generates a large number of IGMP group entries. When the number of IGMP group entries reaches the default limit, new IGMP group entries cannot be generated. The high-specification mode increases the number of IGMP group entries supported on the switch. After this mode is configured, the number of IGMP group entries can reach the maximum number supported by the switch, maximizing the switch's capability to support large-scale multicast applications.

      NOTE:
      • The high-specification mode takes effect after a restart.

      • After the high-specification mode is configured, the default value of the robustness variable changes from 2 to 3, the default value of the other querier present interval changes from 125s to 245s, and the default value of the IGMP general query interval changes from 60s to 120s.

    3. Run multicast routing-enable

      IP multicast routing is enabled.

      By default, the IP multicast routing function is disabled.

    4. Run interface interface-type interface-number

      The interface view is displayed.

    5. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    6. Run igmp enable

      IGMP is enabled on the interface.

      By default, IGMP is disabled on an interface.

  • Enabling IGMP in a virtual private network (VPN) instance

    A VPN instance must exist before you enable IGMP in the VPN instance.

    1. Run system-view

      The system view is displayed.

    2. (Optional) Run set multicast forwarding-table super-mode

      The high-specification mode is configured for multicast forwarding.

    3. Run ip vpn-instance vpn-instance-name

      The VPN instance view is displayed.

    4. Run ipv4-family

      The IPv4 address family is enabled for the VPN instance, and the VPN instance IPv4 address family view is displayed.

    5. Run route-distinguisher route-distinguisher

      An RD is configured for the VPN instance IPv4 address family.

    6. Run multicast routing-enable

      IP multicast routing is enabled.

      By default, the IP multicast routing function is disabled.

    7. Run quit

      Return to the VPN instance view.

    8. Run quit

      Return to the system view.

    9. Run interface interface-type interface-number

      The interface view is displayed.

      NOTE:

      When configuring multi-instance IGMP, you can bind VLANIF interfaces, sub-interfaces, loopback interfaces, or tunnel interfaces to VPN instances. The physical interfaces that have been switched to the Layer 3 mode using the undo portswitch command cannot be bound to VPN instances.

    10. Run ip binding vpn-instance vpn-instance-name

      The interface is bound to a specified VPN instance.

      By default, an interface is a public network interface that is not associated with any VPN instance.

    11. Run igmp enable

      IGMP is enabled on the interface.

      By default, IGMP is disabled on an interface.

Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100065742

Views: 47811

Downloads: 46

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next