No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Multicast

S7700 and S9700 V200R013C00

This document describes the configurations of IP multicast, including IP multicast basics, IGMP, MLD, IPv4 PIM, IPv6 PIM, MSDP, multicast VPN, layer 3 multicast CAC, IPv4 multicast route management, IPv6 multicast route management, IGMP snooping, MLD snooping, static multicast MAC address, multicast VLAN replication, layer 2 multicast CAC, multicast network management.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adjusting Control Parameters for a Multicast Source

Adjusting Control Parameters for a Multicast Source

Pre-configuration Tasks

Before setting the parameters for controlling a multicast source, complete the following task:

Configuring Basic IPv4 PIM-DM Functions

Context

After a PIM device receives a multicast packet from a multicast source, it starts a timer for the (S, G) entry and sets the timer to the lifetime of the source. If the device receives a packet from the source before the timer expires, it resets the timer. If the device does not receive any multicast packet from the source within the lifetime of the source, it considers the corresponding (S, G) entry invalid and deletes this entry.

You can configure the lifetime of the source. To control multicast traffic or ensure data security, configure source address-based filtering policies on the device so that the device accepts only multicast data allowed by the policies.

Default Settings

Table 4-5 lists the default settings of control parameters for a multicast source.

Table 4-5  Default settings of multicast source control parameters
Parameter Default Setting

Keepalive period of a multicast source

210s

Source address filtering policy

No policy configured (Multicast data from all sources is accepted.)

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run pim [ vpn-instance vpn-instance-name ]

    The PIM view is displayed.

  3. Run source-lifetime { interval | infinity } [ group-policy { acl-name acl-name | acl-number } ]

    The lifetime of a multicast source is configured.

  4. Run source-policy { acl-number | acl-name acl-name }

    A multicast source address-based filtering policy is configured.

    • If a basic ACL is specified in the command, the allowed multicast packets are specified by the source parameter in the rule configured under the basic ACL. The device forwards only the multicast packets with the source addresses allowed by the filtering policy.

    • If an advanced ACL is specified in the command, the allowed multicast packets are specified by source and destination parameters in the rule configured under the advanced ACL. The device forwards only the multicast packets with both source addresses and group addresses allowed by the filtering policy.

    • If the specified ACL contains no rule, the device does not forward multicast packets from any sources.

    • The source-policy command does not filter the static (S, G) entries and the PIM entries of the Join messages received from private networks.

Verifying the Configuration

Run the following commands to check the PIM routing table.

  • Run the display pim [ vpn-instance vpn-instance-name | all-instance ] routing-table [ group-address [ mask { group-mask-length | group-mask } ] | source-address [ mask { source-mask-length | source-mask } ] | incoming-interface { interface-type interface-number | register } | outgoing-interface { include | exclude | match } { interface-type interface-number | register | none } | mode { dm | sm | ssm } | flags flag-value | fsm ] * [ outgoing-interface-number [ number ] ] command to check detailed information about the PIM routing table.

  • Run the display pim routing-table [ group-address [ mask { group-mask-length | group-mask } ] | source-address [ mask { source-mask-length | source-mask } ] | incoming-interface { interface-type interface-number | register } | outgoing-interface { include | exclude | match } { interface-type interface-number | vpn-instance vpn-instance-name | register | none } | mode { dm | sm | ssm } | flags flag-value | fsm ] * [ outgoing-interface-number [ number ] ] command to check detailed information about the PIM routing table.

  • Run the display pim [ vpn-instance vpn-instance-name | all-instance ] routing-table brief [ group-address [ mask { group-mask-length | group-mask } ] | source-address [ mask { source-mask-length | source-mask } ] | incoming-interface { interface-type interface-number | register } ] * command to check brief information about the PIM routing table.

Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100065742

Views: 42339

Downloads: 40

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next