No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - MPLS

S7700 and S9700 V200R013C00

This document describes the configurations of MPLS, including Static LSP, MPLS LDP, MPLS QoS, MPLS TE, MPLS OAM, Seamless MPLS.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Creating a Backup CR-LSP

Creating a Backup CR-LSP

Context

CR-LSP backup can be configured to allow traffic to switch from a primary CR-LSP to a backup CR-LSP, providing end-to-end protection.

Perform the following configurations on the ingress node of an MPLS TE tunnel.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface tunnel tunnel-number

    The tunnel interface view is displayed.

  3. Run mpls te backup hot-standby

    or run mpls te backup ordinary

    The mode of establishing a backup CR-LSP is configured.

    If hot-standby is specified, a hot-standby CR-LSP is set up. To implement fast switching at the millisecond level, perform the operation of Configuring Static BFD for CR-LSPs or Configuring Dynamic BFD for CR-LSPs.

    NOTE:

    A tunnel interface cannot be used for both a bypass tunnel and a backup tunnel. A protection failure will occur if the mpls te backup and mpls te bypass-tunnel commands are run on the tunnel interface, or if the mpls te backup and mpls te protected-interface commands are run on the tunnel interface. For details on how to create a bypass CR-LSP, see Configuring Manual TE FRR or Configuring Auto TE FRR.

    A tunnel interface cannot be used for both a bypass tunnel and a protection tunnel in a tunnel protection group. A protection failure will occur if the mpls te backup and mpls te protection tunnel commands are run on the tunnel interface. For details on how to create a protection tunnel, see Configuring a Tunnel Protection Group.

    After hot standby or ordinary backup is configured, the system selects a path for a backup CR-LSP. To specify a path for a backup CR-LSP, repeatedly perform one or more of steps 4 to 6. When hot standby is configured, repeatedly perform one or more of steps 7 to 9.

  4. (Optional) Run mpls te path explicit-path path-name secondary

    An explicit path is specified for the backup CR-LSP.

    Use a separate explicit path for the backup CR-LSP to prevent the backup CR-LSP from completely overlapping its primary CR-LSP. Protection will fail if the backup CR-LSP completely overlaps its primary CR-LSP.

    The mpls te path explicit-path command can be run successfully only after an explicit path is set up by running the explicit-path path-name command in the system view, and the nodes on the path are specified.

  5. (Optional) Run mpls te affinity property properties [ mask mask-value ] secondary

    The affinity property is configured for the backup CR-LSP.

    By default, the affinity property used by the backup CR-LSP is 0x0 and the mask is 0x0.

  6. (Optional) Run mpls te hop-limit hop-limit-value secondary

    The hop limit is set for the backup CR-LSP.

    The default hop limit is 32.

  7. (Optional) Run mpls te backup hot-standby overlap-path

    The path overlapping function is configured. This function allows a hot-standby CR-LSP to use links of a primary CR-LSP.

    By default, the path overlapping function is disabled. If the path overlapping function is disabled, a hot-standby CR-LSP may fail to be set up.

    After the path overlapping function is configured, the path of the hot-standby CR-LSP partially overlaps the path of the primary CR-LSP when the hot-standby CR-LSP cannot exclude paths of the primary CR-LSP.

  8. (Optional) Run mpls te backup hot-standby wtr interval

    The WTR time for a switchback is set.

    By default, the WTR time for switching traffic from a hot-standby CR-LSP to a primary CR-LSP is 10 seconds.

  9. (Optional) Run mpls te backup hot-standby mode { revertive [ wtr interval ] | non-revertive }

    A revertive mode is specified.

    By default, the revertive mode is used.

  10. Run mpls te commit

    The configuration is committed.

Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100065745

Views: 23621

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next