No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - MPLS

S7700 and S9700 V200R013C00

This document describes the configurations of MPLS, including Static LSP, MPLS LDP, MPLS QoS, MPLS TE, MPLS OAM, Seamless MPLS.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting the DiffServ Mode Supported by MPLS L3VPN

Setting the DiffServ Mode Supported by MPLS L3VPN

Context

To provide QoS guarantee for VPN traffic on an MPLS VPN network, set the DiffServ mode according to your needs.
  • If you want to differentiate priorities of different services in a VPN, set the DiffServ mode to uniform. You can also set the DiffServ mode to pipe or short pipe, but you need to specify the DiffServ domain in which the mode applies.

  • If you want to differentiate priorities of services in different VPNs but not priorities of services in a VPN, set the DiffServ mode to pipe or short pipe and specify EXP values in private labels.

If you do not want to change priorities carried in original packets, you are advised to set the DiffServ mode to pipe or short pipe. In uniform and pipe modes, the egress node determines the per-hop behavior (PHB) based on the EXP priorities of packets. In short pipe mode, the egress node determines the PHB based on DSCP priorities of packets.

NOTE:

On FA series cards, the domains with domain IDs 0 to 3 take effect. You can query the domain ID using the display diffserv domain command.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run ip vpn-instance vpn-instance-name

    The VPN instance view is displayed.

  3. Run diffserv-mode { pipe { mpls-exp mpls-exp | domain ds-name } | short-pipe [ mpls-exp mpls-exp ] domain ds-name | uniform [ domain ds-name ] }

    The DiffServ mode supported by the MPLS L3VPN is set.

    By default, the DiffServ mode supported by the MPLS L3VPN is uniform.

    • If the mpls-qos ingress trust upstream none or mpls-qos egress trust upstream none command is configured, the device on the private network does not perform EXP priority mapping even if you run the diffserv-mode command.

    • When the DiffServ mode is set to uniform on the ingress node, the ingress node performs priority mapping in the DiffServ domain specified by the domain parameter in this command. If the domain parameter is not specified, the ingress node performs priority mapping in the DiffServ domain specified by the mpls-qos ingress trust upstream { ds-name | default } command.

    • In a non-PHP scenario, the egress node performs priority mapping in the DiffServ domain specified by the mpls-qos egress trust upstream { ds-name | default } command. In a PHP scenario, the egress node performs priority mapping in the DiffServ domain specified by the domain parameter in this command. If the domain parameter is not specified, the egress node performs priority mapping in the DiffServ domain specified by the mpls-qos egress trust upstream { ds-name | default } command.

    NOTE:

    This command must be configured before the instance takes effect; otherwise, you must reset BGP connections to make the configuration take effect.

Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100065745

Views: 26332

Downloads: 30

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next