No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

S9300, S9300E, and S9300X V200R013C00

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
ENTITYEXTTRAP

ENTITYEXTTRAP

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.3 hwEntityInputRateThresholdAlarm

Description

ENTITYEXTTRAP/2/INUSAGEEXCEED: OID [oid] Input flow bandwidth usage exceeded the threshold. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], CurUsage=[INTEGER], Threshold=[INTEGER])

The inbound bandwidth on the channel of the board exceeds the alarm threshold.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.3 Major qualityOfServiceAlarm(3)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.

The value 65535 indicates that the value is meaningless.

PortID Indicates the port name of the HG channel.
PeerSlotID Indicates the slot ID of the peer board.
CurUsage Indicates the current bandwidth usage.

If the current bandwidth usage cannot be obtained, it displays 0.

Threshold Indicates the bandwidth usage alarm threshold.

Impact on the System

The HG channel may be congested.

Possible Causes

The inbound bandwidth usage of the HG channel exceeds the alarm threshold.

Procedure

  • Collect alarm information and configuration information, and then contact technical support personnel.

Related Information

None

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.4 hwEntityInputRateThresholdAlarmResume

Description

ENTITYEXTTRAP/4/INUSAGERES: OID [oid] Input flow bandwidth usage fell below the threshold. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], CurUsage=[INTEGER], Threshold=[INTEGER])

The inbound bandwidth on the channel of the board falls below the alarm recovery threshold.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.4 Warning qualityOfServiceAlarm(3)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.

The value 65535 indicates that the value is meaningless.

PortID Indicates the port name of the HG channel.
PeerSlotID Indicates the slot ID of the peer board.
CurUsage Indicates the current bandwidth usage.

If the current bandwidth usage cannot be obtained, it displays 0.

Threshold Indicates the bandwidth usage alarm recovery threshold.

Impact on the System

None

Possible Causes

The inbound bandwidth usage of the HG channel falls below the alarm recovery threshold.

Procedure

  1. This alarm is informational and no action is required.

Related Information

None

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.5 hwEntityOutputRateThresholdAlarm

Description

ENTITYEXTTRAP/2/OUTUSAGEEXCEED: OID [oid] Output flow bandwidth usage exceeded the threshold. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], CurUsage=[INTEGER], Threshold=[INTEGER])

The outbound bandwidth usage on the channel of the board exceeds the alarm threshold.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.5 Major qualityOfServiceAlarm(3)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.
PortID Indicates the port name of the HG channel.
PeerSlotID Indicates the slot ID of the peer board.
CurUsage Indicates the current bandwidth usage.
Threshold Indicates the bandwidth usage alarm threshold.

Impact on the System

The HG channel may be congested.

Possible Causes

The outbound bandwidth usage of the HG channel exceeds the alarm threshold.

Procedure

  • Collect alarm information and configuration information, and then contact technical support personnel.

Related Information

None

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.6 hwEntityOutputRateThresholdAlarmResume

Description

ENTITYEXTTRAP/4/OUTUSAGERES: OID [oid] Output flow bandwidth usage fell below the threshold. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], CurUsage=[INTEGER], Threshold=[INTEGER])

The channel bandwidth usage on the channel of the board falls below the alarm recovery threshold.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.6 Warning qualityOfServiceAlarm(3)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.
PortID Indicates the port name of the HG channel.
PeerSlotID Indicates the slot ID of the peer board.
CurUsage Indicates the current bandwidth usage.
NOTE:

If the current bandwidth usage cannot be obtained, it displays 0.

Threshold Indicates the bandwidth usage alarm recovery threshold.

Impact on the System

None

Possible Causes

The outbound bandwidth usage of the HG channel falls below the alarm recovery threshold.

Procedure

  1. This alarm is informational and no action is required.

Related Information

None

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.8 hwEntityHigErrorPacketThresholdAlarm

Description

ENTITYEXTTRAP/2/PKTERRORRISING: OID [oid] Input packets are discarded for an error in physical layer detection. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], ErrorPacketStatistics=[STRING], ErrorPacketThreshold=[STRING], MonitorInterval=[STRING])

The total number of error packets on an HG channel or CSS port exceeds the alarm threshold.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.8 Major communicationsAlarm(2)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.
NOTE:

The value is 0 or 1 for the HG channel or 65535 (an invalid value) for a CSS port.

PortID Indicates the port number of the HG channel or CSS port.
PeerSlotID Indicates the slot ID of the remote card.
ErrorPacketStatistics Indicates the total number of error packets.
ErrorPacketThreshold Alarm threshold for error packets.
MonitorInterval Indicates the detection interval.

Impact on the System

The HG channel or CSS port cannot forward packets normally. During inter-card or inter-chassis traffic forwarding, packets are lost or cannot be forwarded.

Possible Causes

  • The local or remote card is not securely installed.
  • The local or remote card connector is faulty.
  • The local or remote card is faulty.

Procedure

  1. Run the display device command to check whether the cards have registered normally. If the local and remote cards have registered normally, the cards have been securely installed. Otherwise, remove and reinstall the cards and then check whether this alarm persists.
  2. Remove the local and remote cards and then check whether there are bent pins. If pins of one card are bent or damaged, this card is damaged.
  3. Replace the card.

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.9 hwEntityHigStateChangeNotify

Description

ENTITYEXTTRAP/2/HGSTATECHANGE: OID [oid] Higig port state has changed. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], ChangedTimes=[STRING])

The HG channel state has changed.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.9 Major communicationsAlarm(2)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.
PortID Indicates the port number of the HG channel.
PeerSlotID Indicates the slot ID of the remote card.
ChangedTimes Indicates the number of times the HG channel state has changed.

Impact on the System

The HG channel cannot forward packets normally. During inter-card traffic forwarding, packets are lost or cannot be forwarded.

Possible Causes

  • The local or remote card is not securely installed.
  • The local or remote card connector is faulty.
  • The local or remote card is faulty.

Procedure

  1. Run the display device command to check whether the cards have registered normally. If the local and remote cards have registered normally, the cards have been securely installed. Otherwise, remove and reinstall the cards and then check whether this alarm persists.
  2. Remove the local and remote cards and then check whether there are bent pins. If pins of one card are bent or damaged, this card is damaged.
  3. Replace the card.

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.10 hwEntityHigStateDownNotify

Description

ENTITYEXTTRAP/2/HGSTATEDOWN: OID [oid] Higig port state is always DOWN. (SlotID=[STRING], UnitID=[INTEGER], PortID=[STRING], PeerSlotID=[STRING], MonitorInterval=[STRING])

The HG channel state remains Down.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.10 Major communicationsAlarm(2)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.
UnitID Indicates the chip ID.
PortID Indicates the port number of the HG channel.
PeerSlotID Indicates the slot ID of the remote card.
MonitorInterval Indicates the detection interval.

Impact on the System

The HG channel cannot forward packets normally. During inter-card traffic forwarding, packets are lost or cannot be forwarded.

Possible Causes

  • The local or remote card is not securely installed.
  • The local or remote card connector is faulty.
  • The local or remote card is faulty.

Procedure

  1. Run the display device command to check whether the cards have registered normally. If the local and remote cards have registered normally, the cards have been securely installed. Otherwise, remove and reinstall the cards and then check whether this alarm persists.
  2. Remove the local and remote cards and then check whether there are bent pins. If pins of one card are bent or damaged, this card is damaged.
  3. Replace the card.

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.11 hwEntityPositionMismatchNotify

Description

ENTITYEXTTRAP/4/POSMISMATCH: OID [oid] The temperature and fan noise in slot 6 are higher than other slots. Install the board into another slot. (SlotID=[STRING])

The temperature of the board in slot 6 and fan noise are higher than boards in other slots. You are advised to install this board to another slot.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.11 Warning environmentalAlarm(6)

Parameters

Name Meaning
oid Indicates the MIB object ID of the alarm.
SlotID Indicates the slot ID.

Impact on the System

The temperature of the board in slot 6 and fan noise are higher than boards in other slots

Possible Causes

The board is installed to a non-recommended slot.

Procedure

  1. Install the board in slot 6 to another slot.

ENTITYEXTTRAP_1.3.6.1.4.1.2011.5.25.31.2.2.13 hwBoardDropRuntPacketNotify

Description

ENTITYEXTTRAP/4/RUNTPKTDROP: OID [OID] The board has been detected that discards the runt packets, which may affect services. (PhysicalIndex=[INTEGER], PhysicalName=[OCTET], BoardDroppedRuntPkt=[COUNTER64], TimeInterval=[INTEGER])

An alarm is generated when some packets of 64 to 86 bytes or 145 to 193 bytes, which are forwarded by the card at the line rate, are lost.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.31.2.2.13 Warning qualityOfServiceAlarm(3)

Parameters

Name Meaning
OID Indicates the MIB object ID of the alarm.
PhysicalIndex Indicates the index of a card.
PhysicalName Indicates the name of a card.
BoardDroppedRuntPkt Indicates the number of dropped packets.
TimeInterval Indicates the interval at which statistics about dropped packets are collected.

Impact on the System

Packet loss will occur when packets of 64 to 86 bytes or 145 to 193 bytes are forwarded at the line rate.

Possible Causes

The cards forward a high volume of traffic.

Procedure

  1. Expand the capacity or load balance the traffic to reduce the traffic forwarded by the card.
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065855

Views: 3520

Downloads: 2

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next