No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Interface Management

S9300, S9300E, and S9300X V200R013C00

This document describes the interface management configuration, including basic interface configuration, Ethernet interface configuration, and logical interface configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for Ethernet Interfaces

Licensing Requirements and Limitations for Ethernet Interfaces

Involved Network Element

Other network elements are not required.

Licensing Requirements

An Ethernet interface is a basic feature of a switch and is not under license control.

Version Requirements

Table 2-1  Products and versions supporting Ethernet interfaces

Product

Product Model

Version Supporting Different Types of Interfaces

S9300

S9303, S9306, S9312

  • FE electrical interfaces/GE electrical interfaces/FE optical interfaces/GE optical interfaces/XGE optical interfaces:

    V100R002, V100R003, V100R006(C00&C01), V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

  • 40GE optical interfaces:

    V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008 (C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

  • 100GE optical interfaces:

    V200R008 (C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300

S9310

FE electrical interfaces/GE electrical interfaces/FE optical interfaces/GE optical interfaces/XGE optical interfaces/40GE optical interfaces/100GE optical interfaces:

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300X

S9310X

FE electrical interfaces/GE electrical interfaces/FE optical interfaces/GE optical interfaces/XGE optical interfaces/40GE optical interfaces/100GE optical interfaces:

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300E

S9303E, S9306E, S9312E

  • FE electrical interfaces/GE electrical interfaces/FE optical interfaces/GE optical interfaces/XGE optical interfaces/40GE optical interfaces:

    V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

  • 100GE optical interfaces:

    V200R008 (C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • Table 2-2 lists the common attributes of Ethernet interfaces.

    Table 2-2  Common attributes of Ethernet interfaces

    Interface Type

    Common Attributes

    Remarks

    FE electrical interfaces

    • Transmission medium: network cable
    • Rate: 10 Mbit/s and 100 Mbit/s
    • Duplex mode: full-duplex/half-duplex
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: supported

    -

    GE electrical interfaces

    • Transmission medium: network cable
    • Rate: 10 Mbit/s, 100 Mbit/s, and 1000 Mbit/s
    • Duplex mode: full-duplex/half-duplex. When the rate is 1000 Mbit/s, only full-duplex is supported.
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: supported

    For X1E series, X1C series, X1L series, and LE1D2S04SEC0 cards, the duplex mode cannot be configured for interfaces working in either auto-negotiation or non-auto-negotiation mode.

    FE optical interfaces

    • Transmission medium: FE optical module
    • Rate: 100 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported

    -

    GE optical interfaces

    When the transmission medium is an FE optical module:
    • Rate: 100 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is a GE optical module:
    • Rate: 100 Mbit/s and 1000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: supported
    When the transmission medium is a GE copper module:
    • Rate: 10 Mbit/s, 100 Mbit/s, and 1000 Mbit/s
    • Duplex mode: full-duplex/half-duplex. When the rate is 1000 Mbit/s, only full-duplex is supported.
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: supported
    • By default, auto-negotiation is enabled on GE optical interfaces and rate auto-negotiation is disabled. You can run the speed auto-negotiation command to enable rate auto-negotiation.
    • After a copper module is installed on a GE optical interface of an X2E/X2S/X2L series card, the interface can work at the rate of 100 Mbit/s or 1000 Mbit/s (including forcible configuration and auto-sensing), and cannot work at the rate of 10 Mbit/s. When the interface works as an optical interface, it can only work at the rate of 1000 Mbit/s, and cannot work at the rate of 100 Mbit/s.

    XGE (10GE) optical interface

    When the transmission medium is an XGE optical module:
    • Rate: 10000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is an XGE or GE optical module:
    • Rate: 1000 Mbit/s and 10000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is a GE optical module:
    • Rate: 1000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is a GE copper module:
    • Rate: 1000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: supported
    • Only cards with MAB version 1 in V200R007 and later versions support XGE/GE optical modules. The cards include:
      • SC series, LE0DX16SFC00, and LE0DX40SFC00 cards of the S9300
      • SC series, LE0DX16SFC00, LE0DX40SFC00, and LE2D2X48SEC0 cards of the S9300E
      • SC series, LE0DX16SFC00, LE0DX40SFC00, and LE2D2X48SEC0 cards of the S9300X
    • Assume that an XGE optical interface has an XGE/GE optical module installed and the interface rate is set to 1000 Mbit/s using the speed auto 1000 command. When you run the display interface command on the interface, the command output shows that auto-negotiation is enabled. However, you cannot run the negotiation auto command to configure the auto-negotiation mode.

    • The XGE optical interfaces on the LE2D2X08SED4, LE0DX12XSA00, LE2D2X08SED4, LE1D2S04SX1E, LE1D2S04SX1C, LE1D2S08SX1E, and LE1D2S04SEC0 cards of the S9300 do not support GE copper modules.
    • The XGE optical interfaces on the LE2D2X08SED4, LE0DX12XSA00, LE2D2X08SED4, LE1D2S04SX1E, LE1D2S04SX1C, LE1D2S08SX1E, and LE1D2S04SEC0 cards of the S9300E do not support GE copper modules.
    • The XGE optical interfaces on the LE2D2X08SED4, LE0DX12XSA00, LE2D2X08SED4, LE1D2S04SX1E, LE1D2S04SX1C, LE1D2S08SX1E, and LE1D2S04SEC0 cards of the S9300X do not support GE copper modules.
    • After a GE copper module is installed on an XGE interface of an X2E/X2H/X2S/X2L series card or LE1D2X32SEC0 card, the interface can work at the rate of 100 Mbit/s or 1000 Mbit/s, and cannot work at the rate of 10 Mbit/s.
    • After a 1000M optical module is installed on an XGE interface of an X2E/X2H/X2S/X2L series card or LE1D2X32SEC0 card, the interface can work at the rate of 1000 Mbit/s.

    40GE optical interfaces

    When the transmission medium is a 40GE optical module:
    • Rate: 40000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is a high-speed cable:
    • Rate: 40000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    • When you run the display interface command on a 40GE optical interface that has a high-speed cable installed, the command output shows that auto-negotiation is enabled. However, you cannot run the negotiation auto command to configure the auto-negotiation mode.
    • After a 40GE stack interface is connected to a high-speed cable, the 40GE optical interfaces on the LE1D2SRUKC00, LE1D2SRUKC01*, LE1D2SFUK000, LX1D2MFUXC00, and LX1D2SFUX000 of the S9310 do not support auto-negotiation.
    100GE optical interfaces
    When the transmission medium is a 100GE optical module:
    • Rate: 100000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is a 40GE optical module:
    • Rate: 40000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: not supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    When the transmission medium is a high-speed cable:
    • Rate: 40000 Mbit/s and 100000 Mbit/s
    • Duplex mode: full-duplex
    • Auto-negotiation: supported
    • Flow control: supported
    • Flow control auto-negotiation: not supported
    • Only the EE series cards, LE1D2C04HX2E, LE1D2C04HX2S, LE3D2C04HX2L, LE1D2H02QX2E, LE1D2H02QEC0 and LE1D2H02QX2S cards support 100GE interfaces.
    • 100GE interfaces on the EE series cards can only have 100GE optical modules installed.
    • After a 40GE optical module or 40GE high-speed cable is installed on a 100GE interface of an X2E/X2H/X2S/X2L series card or LE1D2H02QEC0 card, the interface can work at the rate of 40 Gbit/s.
  • X1E, X2E, X1C, X1L, X2L, X2S, and X2Hcards, LE1D2X32SEC0, LE1D2H02QEC0 and LE1D2S04SEC0 cards do not support the duplex mode configuration.
  • The LE0DG48TBC00 and LE0DG48SBC00 cards do not support flow control or flow control auto-negotiation.

  • On the S9300, only the LE1D2L02QFC0 interface card supports the IFG configuration.

    On the S9300X, only the LE1D2L02QFC0 interface card supports the IFG configuration.

    On the S9300E, only the LE1D2L02QFC0 interface card supports the IFG configuration.

  • On the S series switches, only the E series cards (excluding EE cards and LE0DG24CEAS0 card), LE0DX12XSA00 card, and SC cards in the S series, and FC cards in the F series support unidirectional single-fiber communication. A license is required.

Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065861

Views: 4951

Downloads: 8

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next