No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S9300, S9300E, and S9300X V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, NSR Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Association Between VRRP and Peer BFD to Implement a Rapid Active/Standby Switchover

Configuring Association Between VRRP and Peer BFD to Implement a Rapid Active/Standby Switchover

Context

When a VRRP group is faulty, the backup with the highest priority detects the fault and switches to the master after the Master_Down_Interval timer expires. The switchover period is at least 3s. During this switchover period, service traffic is still sent to the original master, causing loss of user traffic. In Figure 3-14, a peer BFD session is configured between SwitchA and SwitchB and used to rapidly detect communication faults of the VRRP group. When the BFD session detects a fault, an active/standby switchover is triggered immediately. This millisecond-level switchover reduces traffic loss.

After the fault is rectified, the VRRP group status on SwitchA and SwitchB is restored through VRRP negotiation.

NOTE:
  • A VRRP group can be associated only with a static BFD session or a static BFD session with automatically negotiated discriminators.

  • The master and backup in the VRRP group must work in preemption mode. It is recommended that the preemption delay be 0 on the backup and non-zero on the master.

  • Multiple VRRP groups can monitor a BFD session, and a VRRP group can monitor a maximum of eight BFD sessions simultaneously.

Figure 3-14  Association between VRRP and peer BFD to implement a rapid active/standby switchover

Procedure

  1. Configure a static BFD session or a static BFD session with automatically negotiated discriminators. For details, see Configuring Single-Hop BFD, Configuring Multi-Hop BFD, and Configuring Static BFD with Automatically Negotiated Discriminators.
  2. Run system-view

    The system view is displayed.

  3. Run interface interface-type interface-number.subinterface-number

    The view of the sub-interface on the backup where the VRRP group is configured is displayed.

  4. Run vrrp vrid virtual-router-id track bfd-session { bfd-session-id | session-name bfd-configure-name } peer

    Association between a VRRP group and a peer BFD session is configured.

    NOTE:
    When associating a VRRP group with a BFD session, note the following points:
    • If session-name bfd-configure-name is specified, a VRRP group can be bound only to a static BFD session with automatically negotiated discriminators.

    • If bfd-session-id is specified, the VRRP group can be bound only to a static BFD session.

    • If a VRRP group is bound to an mVRRP group, the mVRRP group maintains the VRRP group status, and the VRRP group is unable to monitor any BFD sessions.

    • If session-name bfd-configure-name is specified, a VRRP group can be bound only to a static BFD session with automatically negotiated discriminators.

    • If bfd-session-id is specified, a VRRP group can be bound only to a static BFD session.

    • If a VRRP group is bound to an mVRRP group, the mVRRP group maintains the VRRP group status, and the VRRP group is unable to monitor any BFD sessions.

    • If session-name bfd-configure-name is specified, a VRRP group can be bound only to a static BFD session with automatically negotiated discriminators.

    • If bfd-session-id is specified, a VRRP group can be bound only to a static BFD session.

    • If a VRRP group is bound to an mVRRP group, the mVRRP group maintains the VRRP group status, and the VRRP group is unable to monitor any BFD sessions.

Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065868

Views: 16706

Downloads: 8

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next