No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S9300, S9300E, and S9300X V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, NSR Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a VRRP6 Group in Active/Standby Mode

Example for Configuring a VRRP6 Group in Active/Standby Mode

Networking Requirements

In Figure 3-24, HostA is dual-homed to SwitchA and SwitchB through the switch on the IPv6 network. To ensure nonstop service transmission, a VRRP6 group in active/standby mode needs to be configured on SwitchA and SwitchB.
  • The host uses SwitchA as the default gateway to connect to the Internet. When SwitchA becomes faulty, SwitchB functions as the gateway. This implements gateway backup.

  • After SwitchA recovers, it preempts to be the master to transmit data after a preemption delay of 20s.

NOTE:

In this scenario, to avoid loops, ensure that all connected interfaces have STP disabled and connected interfaces are removed from VLAN 1. If STP is enabled and VLANIF interfaces of switches are used to construct a Layer 3 ring network, an interface on the network will be blocked. As a result, Layer 3 services on the network cannot run normally.

Figure 3-24  Networking diagram for configuring a VRRP6 group in active/standby mode

Device

Interface

VLANIF Interface

IP Address

SwitchA

GE1/0/1

VLANIF 300

2002::1/64

GE1/0/2

VLANIF 100

FC00::1/64

SwitchB

GE1/0/1

VLANIF 200

2001::1/64

GE1/0/2

VLANIF 100

FC00::2/64

SwitchC

GE1/0/1

VLANIF 300

2002::2/64

GE1/0/2

VLANIF 200

2001::2/64

GE1/0/3

VLANIF 400

2003::2/64

Configuration Roadmap

The configuration roadmap is as follows:

  1. Assign an IP address to each interface and configure a routing protocol to ensure network connectivity.
  2. Configure a VRRP6 group on SwitchA and SwitchB, set the preemption delay to 20s and a higher priority for SwitchA so that SwitchA functions as the master to forward traffic, and set a lower priority for SwitchB so that SwitchB functions as the backup.

Procedure

  1. Configure devices to ensure network connectivity.

    # Configure VLANs to which each interface belongs. SwitchA is used as an example. The configurations of SwitchB and SwitchC are similar to the configuration of SwitchA. For details, see the configuration files.

    <Quidway> system-view
    [Quidway] sysname SwitchA
    [SwitchA] vlan batch 100 300
    [SwitchA] interface gigabitethernet 1/0/1
    [SwitchA-GigabitEthernet1/0/1] port hybrid pvid vlan 300
    [SwitchA-GigabitEthernet1/0/1] port hybrid untagged vlan 300
    [SwitchA-GigabitEthernet1/0/1] quit
    [SwitchA] interface gigabitethernet 1/0/2
    [SwitchA-GigabitEthernet1/0/2] port hybrid pvid vlan 100
    [SwitchA-GigabitEthernet1/0/2] port hybrid untagged vlan 100
    [SwitchA-GigabitEthernet1/0/2] quit
    

    # Assign an IP address to each interface. SwitchA is used as an example. The configurations of SwitchB and SwitchC are similar to the configuration of SwitchA. For details, see the configuration files.

    [SwitchA] ipv6
    [SwitchA] interface vlanif 100
    [SwitchA-Vlanif100] ipv6 enable
    [SwitchA-Vlanif100] ipv6 address FC00::1 64
    [SwitchA-Vlanif100] quit
    [SwitchA] interface vlanif 300
    [SwitchA-Vlanif300] ipv6 enable
    [SwitchA-Vlanif300] ipv6 address 2002::1 64
    [SwitchA-Vlanif300] quit

    # Configure Layer 2 transmission on the switch.

    <Quidway> system-view
    [Quidway] sysname Switch
    [Switch] vlan 100
    [Switch-vlan100] quit
    [Switch] interface gigabitethernet 1/0/1
    [Switch-GigabitEthernet1/0/1] port hybrid pvid vlan 100
    [Switch-GigabitEthernet1/0/1] port hybrid untagged vlan 100
    [Switch-GigabitEthernet1/0/1] quit
    [Switch] interface gigabitethernet 1/0/2
    [Switch-GigabitEthernet1/0/2] port hybrid pvid vlan 100
    [Switch-GigabitEthernet1/0/2] port hybrid untagged vlan 100
    [Switch-GigabitEthernet1/0/2] quit
    

    # Configure OSPFv3 between SwitchA, SwitchB, and SwitchC. SwitchA is used as an example. The configurations of SwitchB and SwitchC are similar to the configuration of SwitchA. For details, see the configuration files.

    [SwitchA] ospfv3
    [SwitchA-ospfv3-1] router-id 1.1.1.1
    [SwitchA-ospfv3-1] quit
    [SwitchA] interface vlanif 100
    [SwitchA-Vlanif100] ospfv3 1 area 0
    [SwitchA-Vlanif100] quit
    [SwitchA] interface vlanif 300
    [SwitchA-Vlanif300] ospfv3 1 area 0
    [SwitchA-Vlanif300] quit

  2. Configure VRRP6 groups.

    # Configure VRRP6 group 1 on SwitchA, and set the priority of SwitchA to 120 and the preemption delay to 20s.

    [SwitchA] interface vlanif 100
    [SwitchA-Vlanif100] vrrp6 vrid 1 virtual-ip FE80::1 link-local
    [SwitchA-Vlanif100] vrrp6 vrid 1 virtual-ip FC00::100
    [SwitchA-Vlanif100] vrrp6 vrid 1 priority 120
    [SwitchA-Vlanif100] vrrp6 vrid 1 preempt-mode timer delay 20
    [SwitchA-Vlanif100] quit
    

    # Configure VRRP6 group 1 on SwitchB, and set the default priority of 100 for SwitchB.

    [SwitchB] interface vlanif 100
    [SwitchB-Vlanif100] vrrp6 vrid 1 virtual-ip FE80::1 link-local
    [SwitchB-Vlanif100] vrrp6 vrid 1 virtual-ip FC00::100
    [SwitchB-Vlanif100] quit

  3. Verify the configuration.

    # Run the display vrrp6 command on SwitchA and SwitchB. You can see that SwitchA is in Master state and SwitchB is in Backup state.

    [SwitchA] display vrrp6
    Vlanif100 | Virtual Router 1
       State : Master
       Virtual IP : FE80::1
                    FC00::100
       Master IP : FE80::218:82FF:FED3:2AF3
       PriorityRun : 120
       PriorityConfig : 120
       MasterPriority : 120
       Preempt : YES      Delay Time : 20 s
       TimerRun : 100 cs
       TimerConfig : 100 cs
       Virtual MAC : 0000-5e00-0201 
       Check hop limit : YES
       Config type : normal-vrrp
       Backup-forward : disabled
       Create time : 2012-01-12 20:15:46
       Last change time : 2012-01-12 20:15:46
    [SwitchB] display vrrp6
    Vlanif100 | Virtual Router 1
       State : Backup
       Virtual IP : FE80::1
                    FC00::100
       Master IP : FE80::218:82FF:FED3:2AF3
       PriorityRun : 100
       PriorityConfig : 100
       MasterPriority : 120
       Preempt : YES      Delay Time : 0 s
       TimerRun : 100 cs
       TimerConfig : 100 cs
       Virtual MAC : 0000-5e00-0201
       Check hop limit : YES
       Config type : normal-vrrp
       Backup-forward : disabled
       Create time : 2012-01-12 20:15:46
       Last change time : 2012-01-12 20:15:46

    # Run the shutdown command on GE1/0/2 of SwitchA to simulate a link fault.

    [SwitchA] interface gigabitethernet 1/0/2
    [SwitchA-GigabitEthernet1/0/2] shutdown
    [SwitchA-GigabitEthernet1/0/2] quit
    

    # Run the display vrrp6 command on SwitchA and SwitchB. You can see that SwitchA is in Initialize state and SwitchB is in Master state.

    [SwitchA] display vrrp6
    Vlanif100 | Virtual Router 1
       State : Initialize
       Virtual IP : FE80::1
                    FC00::100
       Master IP : ::
       PriorityRun : 120
       PriorityConfig : 120
       MasterPriority : 0
       Preempt : YES      Delay Time : 20 s
       TimerRun : 100 cs
       TimerConfig : 100 cs
       Virtual MAC : 0000-5e00-0201 
       Check hop limit : YES
       Config type : normal-vrrp
       Backup-forward : disabled
       Create time : 2012-01-12 20:15:46
       Last change time : 2012-01-12 20:15:46
    [SwitchB] display vrrp6
    Vlanif100 | Virtual Router 1
       State : Master
       Virtual IP : FE80::1
                    FC00::100
       Master IP : FE80::218:82FF:FE68:7455
       PriorityRun : 100
       PriorityConfig : 100
       MasterPriority : 100
       Preempt : YES      Delay Time : 0 s
       TimerRun : 100 cs
       TimerConfig : 100 cs
       Virtual MAC : 0000-5e00-0201 
       Check hop limit : YES
       Config type : normal-vrrp
       Backup-forward : disabled
       Create time : 2012-01-12 20:15:46
       Last change time : 2012-01-12 20:15:46

    # Run the undo shutdown command on GE1/0/2 of SwitchA.

    [SwitchA] interface gigabitethernet 1/0/2
    [SwitchA-GigabitEthernet1/0/2] undo shutdown
    [SwitchA-GigabitEthernet1/0/2] quit
    

    # After 20s, run the display vrrp6 command on SwitchA and SwitchB. You can see that SwitchA is in Master state and SwitchB is in Backup state.

    [SwitchA] display vrrp6
    Vlanif100 | Virtual Router 1
       State : Master
       Virtual IP : FE80::1
                    FC00::100
       Master IP : FE80::218:82FF:FED3:2AF3
       PriorityRun : 120
       PriorityConfig : 120
       MasterPriority : 120
       Preempt : YES      Delay Time : 20 s
       TimerRun : 100 cs
       TimerConfig : 100 cs
       Virtual MAC : 0000-5e00-0201 
       Check hop limit : YES
       Config type : normal-vrrp
       Backup-forward : disabled
       Create time : 2012-01-12 20:15:46
       Last change time : 2012-01-12 20:15:46
    [SwitchB] display vrrp6
    Vlanif100 | Virtual Router 1
       State : Backup
       Virtual IP : FE80::1
                    FC00::100
       Master IP : FE80::218:82FF:FED3:2AF3
       PriorityRun : 100
       PriorityConfig : 100
       MasterPriority : 120
       Preempt : YES      Delay Time : 0 s
       TimerRun : 100 cs
       TimerConfig : 100 cs
       Virtual MAC : 0000-5e00-0201
       Check hop limit : YES
       Config type : normal-vrrp
       Backup-forward : disabled
       Create time : 2012-01-12 20:15:46
       Last change time : 2012-01-12 20:15:46

Configuration Files

  • SwitchA configuration file

    #
    sysname SwitchA
    #
    ipv6
    #
    vlan batch 100 300
    #
    ospfv3 1
     router-id 1.1.1.1
    #
    interface Vlanif100
     ipv6 enable
     ipv6 address FC00::1/64
     ospfv3 1 area 0.0.0.0
     vrrp6 vrid 1 virtual-ip FE80::1 link-local
     vrrp6 vrid 1 virtual-ip FC00::100
     vrrp6 vrid 1 priority 120
     vrrp6 vrid 1 preempt-mode timer delay 20
    #
    interface Vlanif300
     ipv6 enable
     ipv6 address 2002::1/64
     ospfv3 1 area 0.0.0.0
    #
    interface GigabitEthernet1/0/1
     port hybrid pvid vlan 300
     port hybrid untagged vlan 300
    #
    interface GigabitEthernet1/0/2
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    return
  • SwitchB configuration file

    #
    sysname SwitchB
    #
    ipv6
    #
    vlan batch 100 200
    #
    ospfv3 1
     router-id 2.2.2.2
    #
    interface Vlanif100
     ipv6 enable
     ipv6 address FC00::2/64
     ospfv3 1 area 0.0.0.0
     vrrp6 vrid 1 virtual-ip FE80::1 link-local
     vrrp6 vrid 1 virtual-ip FC00::100
    #
    interface Vlanif200
     ipv6 enable
     ipv6 address 2001::1/64
     ospfv3 1 area 0.0.0.0
    #
    interface GigabitEthernet1/0/1
     port hybrid pvid vlan 200
     port hybrid untagged vlan 200
    #
    interface GigabitEthernet1/0/2
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    return
  • SwitchC configuration file

    #
    sysname SwitchC
    #
    ipv6
    #
    vlan batch 200 300 400
    #
    ospfv3 1
     router-id 3.3.3.3
    #
    interface Vlanif200
     ipv6 enable
     ipv6 address 2001::2/64
     ospfv3 1 area 0.0.0.0
    #
    interface Vlanif300
     ipv6 enable
     ipv6 address 2002::2/64
     ospfv3 1 area 0.0.0.0
    #
    interface Vlanif400
     ipv6 enable
     ipv6 address 2003::2/64
     ospfv3 1 area 0.0.0.0
    #
    interface GigabitEthernet1/0/1
     port hybrid pvid vlan 300
     port hybrid untagged vlan 300
    #
    interface GigabitEthernet1/0/2
     port hybrid pvid vlan 200
     port hybrid untagged vlan 200
    #
    interface GigabitEthernet1/0/3
     port hybrid pvid vlan 400
     port hybrid untagged vlan 400
    #
    return
  • Switch configuration file

    #
    sysname Switch
    #
    vlan batch 100
    #
    interface GigabitEthernet1/0/1
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    interface GigabitEthernet1/0/2
     port hybrid pvid vlan 100
     port hybrid untagged vlan 100
    #
    return
Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065868

Views: 16811

Downloads: 8

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next