No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S9300, S9300E, and S9300X V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, NSR Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Association Between VRRP6 and BFD to Implement a Rapid Active/Standby Switchover

Configuring Association Between VRRP6 and BFD to Implement a Rapid Active/Standby Switchover

Context

You can associate a VRRP6 group with a BFD session. When the BFD session status changes, BFD notifies the VRRP6 group. This process triggers a rapid active/standby switchover.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The view of the interface where a VRRP6 group is configured is displayed.

  3. (Optional) On an Ethernet interface, run undo portswitch

    The interface is switched to Layer 3 mode.

    By default, an Ethernet interface works in Layer 2 mode.

  4. Run vrrp6 vrid virtual-router-id track bfd-session { session-id | session-name bfd-configure-name } [ increased value-increased | reduced value-reduced ]

    Association between VRRP6 and BFD is configured to implement a rapid active/standby switchover.

    increased value-increased: specifies the value by which the priority increases when the monitored BFD session goes Down. The value is an integer that ranges from 1 to 255. The value 255 is reserved for the IP address owner, so the maximum value of value-increased is 254. This parameter is valid only when the VRRP6 group is in Backup state.

    reduced value-reduced: specifies the value by which the priority decreases when the monitored BFD session goes Down. The value is an integer that ranges from 1 to 254. The lowest priority is 1. When the priority is decreased to 1, the master sends a VRRP6 Advertisement packet with priority 0. The value 0 is reserved. When the backup receives a VRRP6 Advertisement packet with priority 0, the backup becomes the master immediately. By default, the value is 10.

    NOTE:

    When setting the value by which the priority increases or decreases, ensure that the backup has a higher priority than the master. This ensures that a rapid active/standby switchover is performed.

    When associating a VRRP6 group with a BFD session, note the following points:

    • If session-name bfd-configure-name is specified, the VRRP6 group can be bound only to a static BFD session with automatically negotiated discriminators.

    • If session-id is specified, the VRRP6 group can be bound only to a static BFD session.

    Currently, the device supports only association between VRRP6 and BFD for IPv4.

    When a BFD session is associated with VRRP or static route, the system does not allow the associated BFD session to be deleted by default. To delete the associated BFD session, run the bfd session nonexistent-config-check disable command to disable the device from checking whether the associated BFD session is deleted.

Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065868

Views: 15874

Downloads: 5

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next