No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S9300, S9300E, and S9300X V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, NSR Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Unidirectional Link Detection When a Single Neighbor Exists

Unidirectional Link Detection When a Single Neighbor Exists

A Link Is Unidirectional Before DLDP Is Enabled

In Figure 5-4, DLDP is enabled between the optical fibers connecting two switches.

Figure 5-4  Intersected fibers

When DLDP is enabled, interfaces in Up state enter the Active state and send Advertisement packets with RSY tags to notify neighbors and request neighbor information. The following uses Interface 1 as an example to describe the detection process:

  1. When receiving an Advertisement packet with the RSY tag from Interface 4, Interface 1 regards that it has detected a neighbor. Interface 1 starts the echo timer, sets up a neighbor entry, and starts the entry aging timer. Interface 1 then enters the Probe state and sends probe packets to detect Interface 4.

  2. Interface 4 cannot receive the probe packets from Interface 1, so Interface 1 will not receive echo packets from Interface 4. When the echo timer on Interface 1 times out, Interface 1 enters the Disable state.

The detection process on other interfaces is similar to that on Interface 1. At last, the four interfaces enter the Disable state.

A Link Changes from Bidirectional to Unidirectional After DLDP Is Enabled

As shown in Figure 5-5, optical fibers connect switches.

Figure 5-5  Correct optical fiber connections when a single neighbor exists

When the Tx and Rx optical fibers are working properly, Switch A and Switch B establish a bidirectional relationship as follows:

  1. When DLDP is enabled, Interface 1 in Up state enters the Active state and sends Advertisement packets with RSY tags to notify neighbors and request neighbor information.

  2. When receiving an Advertisement packet with the RSY tag from Interface 1, Interface 2 regards that it has detected a neighbor. Interface 2 then starts the echo timer, sets up a neighbor entry, and starts the entry aging timer. Interface 2 enters the Probe state and sends a probe packet.

  3. Upon receiving the probe packet, Interface 1 sets up a neighbor entry, enters the Probe state, and returns an echo packet to Interface 2.

  4. When Interface 2 receives the echo packet, it finds that the neighbor entry exists, and the information about the neighbor carried by the echo packet is the same as that saved on the local device. Interface 2 marks the connection with this neighbor as bidirectional.

  5. Interface 2 transitions from the Probe state to the Advertisement state, and periodically sends Advertisement packets. Interface 2 in Advertisement state resets the aging timer for a known neighbor each time a packet is received from the neighbor.

The process for sending Advertisement packets from Interface 2, and setting up a neighbor on Interface 1, is similar to steps 1 to 4 in the preceding explanation. Once these processes have been completed, Interface 1 and Interface 2 regard each other as neighbors with a bidirectional connection.

In Figure 5-6, the Rx optical fiber of Interface 2 has failed and cannot receive an optical signal. When this occurs, Interface 2 enters the Inactive state and stops sending and receiving packets. The Tx optical fiber of Interface 2 remains normal, so Interface 1 can receive signals and remain in Up state. Interface 1 cannot receive DLDPDUs from Interface 2 before the entry aging timer phases out.

Figure 5-6  Disconnection of one optical fiber when a single neighbor exists

The procedure for detecting unidirectional links varies depending on either of the configured DLDP working modes as follows:

  • Normal mode: Interface 1 deletes the neighbor entry, enters the Active state, and sends an Advertisement packet with the RSY tag when the entry aging timer times out. After 5 seconds in Active state, Interface 1 enters the Advertisement state. Then Interface 1 retains in Advertisement state and has no neighbor. Interface 2 retains the Inactive state. In this case, DLDP cannot detect unidirectional links.

  • Enhanced mode: Interface 1 starts the enhanced timer and echo timer and sends a probe packet to the neighbor when the entry aging timer times out. The Tx optical fiber of Interface 1 is disconnected, making Interface 1 unable to receive the echo packet from Interface 2. When the echo timer times out, Interface 1 enters the Disable state and sends a disable packet to the neighbor. In addition, Interface 1 deletes the neighbor entry and starts the RecoverProbe timer to check whether the Tx optical fiber is restored. Interface 2 retains the Inactive state.

    • In enhanced mode, Interface 2 is physically Down, but Interface 1 cannot detect the change. DLDP supports the fast Link-Down notification mechanism that can rapidly detect a fault on the link connecting Interface 1 and Interface 2 before the entry aging timer times out. Upon detecting that Interface 2 is Down, the physical layer sends a Link-Down notification packet to Interface 1. When receiving the Link-Down notification packet, Interface 1 enters the Disable state.

    • The fast Link-Down notification mechanism applies only to the enhanced mode.

Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065868

Views: 15826

Downloads: 3

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next