No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Reliability

S9300, S9300E, and S9300X V200R013C00

This document describes the configurations of Reliability, including BFD Configuration, VRRP Configuration, NSR Configuration, DLDP Configuration, Smart Link and Monitor Link Configuration, MAC Swap Loopback Configuration, EFM Configuration, CFM Configuration, Y.1731 Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Setting EFM OAMPDU Parameters

(Optional) Setting EFM OAMPDU Parameters

Context

EFM entities exchange OAMPDUs periodically to report the link status. Network administrators can set EFM OAMPDU parameters to effectively manage networks.

EFM OAMPDU parameters include the maximum OAMPDU size, interval at which OAMPDUs are sent, and timeout interval at which OAMPDUs are received.
  • After the maximum OAMPDU size is set on an interface, the interface considers excess EFM OAMPDUs invalid and discards them. You can adjust the maximum size of an EFM OAMPDU so that devices can communicate.

  • After setting up an EFM connection, two EFM entities exchange OAMPDUs at a specific interval to check for a properly working connection. If an EFM entity does not receive any OAMPDU from its remote EFM entity within the interval at which OAMPDUs are received, the link is considered as not working properly. Network administrators can set different intervals at which OAMPDUs are received based on user requirements. A short interval can be set for high-priority or delay-sensitive services. A long interval can be set for low-priority or delay-insensitive services.

EFM can be configured on Layer 2 and Layer 3 Ethernet interfaces. By default, an Ethernet interface works in Layer 2 mode. Before configuring EFM on a Layer 3 Ethernet interface, switch the Ethernet interface to Layer 3 mode.

Perform the following steps on the interfaces at both ends of a link.

Procedure

  • Setting the maximum size of an EFM OAMPDU

    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The view of the interface at one end of the link is displayed.

    3. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    4. Run efm packet max-size size

      The maximum size of an EFM OAMPDU is set.

      By default, the maximum size of an EFM OAMPDU on an interface is 128 bytes.

      If the maximum EFM OAMPDU sizes configured on the interfaces at both ends of a link are different, the interfaces negotiate the maximum EFM OAMPDU size during the discovery process. The smaller one between the maximum EFM OAMPDU sizes on the two ends is used.

  • Setting the timeout interval at which EFM OAMPDUs are received

    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The view of the interface at one end of the link is displayed.

    3. (Optional) On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

    4. Run efm timeout timeout-value

      The timeout interval at which EFM OAMPDUs are received is set.

      By default, the timeout interval at which EFM OAMPDUs are received is 5000 ms.

      The interfaces at both ends of a link must use the same timeout interval. Otherwise, session negotiation between the two interfaces fails or the session flaps.

      NOTE:

      The timeout interval is set only after EFM is enabled globally and before EFM is enabled on an interface.

Translation
Download
Updated: 2019-04-09

Document ID: EDOC1100065868

Views: 22310

Downloads: 13

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next