No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Basic Configuration

S2720, S5700, and S6720 V200R013C00

This document describes the configurations of Basic, including CLI Overview, EasyDeploy Configuration, USB-based Deployment Configuration, Logging In to a Device for the First Time, CLI Login Configuration, Web System Login Configuration, File Management, Configuring System Startup, BootLoad Menu Operation.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for USB-based Deployment

Licensing Requirements and Limitations for USB-based Deployment

Involved Network Elements

Other network elements are not required.

Licensing Requirements

USB-based deployment is a basic feature of a switch and is not under license control.

Version Requirements

Table 4-1  Products and versions supporting USB-based deployment

Series

Product Model

Software Version

S2700 S2700SI/S2700EI Not supported
S2710SI Not supported
S2720EI Not supported
S2750EI Not supported
S3700 S3700SI/S3700EI Not supported
S3700HI Not supported
S5700 S5700LI (Only the S5700-52X-LI-48CS-AC, S5701-28X-LI-24S-AC, S5701-28X-LI-AC, S5700-28X-LI-24S-DC, and S5700-28X-LI-24S-AC support USB-based deployment.) V200R003(C00&C02&C10), V200R005C00SPC300, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00
S5700S-LI (Only the S5700S-28X-LI-AC and S5700S-52X-LI-AC support USB-based deployment.) V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00
S5710-C-LI

V200R001C00

S5710-X-LI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S5700SI

V100R005C01, V100R006C00, V200R001C00, V200R002C00, V200R003C00, V200R005C00

S5700EI Not supported
S5710EI

V200R001C00, V200R002C00, V200R003C00, V200R005(C00&C02)

S5720EI

V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5720LI/S5720S-LI (Models that support USB ports)

V200R010C00, V200R011C00, V200R011C10, V200R012(C00&C20), V200R013C00

S5700HI

V100R006C01, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00SPC500&C01&C02)

S5710HI

V200R003C00, V200R005(C00&C02&C03)

S5720HI

V200R006C00, V200R007(C00&C10), V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5730HI

V200R012C00, V200R013C00

S5720SI/S5720S-SI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S5720I-SI

V200R012C00, V200R013C00

S5730SI

V200R011C10, V200R012C00, V200R013C00

S5730S-EI

V200R011C10, V200R012C00, V200R013C00

S6700 S6700EI

V100R006C00, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005(C00&C01&C02)

S6720EI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720S-EI

V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720HI

V200R012C00, V200R013C00

S6720LI/S6720S-LI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

S6720SI/S6720S-SI

V200R011C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

Before USB-based deployment

  • USB-based deployment is mutually exclusive with the SVF, web initial login mode and EasyDeploy functions.
  • Before using a USB flash drive to upgrade a device, ensure that the device can start successfully and has sufficient space to store the required files.
  • Devices to be deployed are unconfigured devices and do not have security measures configured. Therefore, when onsite non-professionals perform deployment task, ensure that they do not perform any unauthorized operations on the devices, USB flash drive, and deployment files.

  • Only one USB flash drive can be connected to a device.
  • Fields in an index file are restricted by the current system version. For example, if some fields in the index file are not supported by the current system version, these fields are invalid for an upgrade to a later version.
  • A smart_config.ini index file supports encryption and HMAC check for a configuration file, whereas a usbload_config.txt index file does not. Therefore, if upgrade files include a configuration file, you are advised to make a smart_config.ini index file, configure an encryption password for the configuration file, and enable HMAC check to enhance security.
  • In V200R005C00 and later versions, USB-based deployment using a smart_config.ini index file is supported, and this deployment mode is supported in a stack. The USB flash drive must be connected to the master switch of the stack. If it is connected to the standby switch or a slave switch, the USB-based deployment process will not start.
  • The S5710-X-LI, S5720SI, S5720I-SI, S6720SI, S6720S-SI, S5720S-SI, S5720LI, S5700S-LI (only the S5700S-28X-LI-AC, S5700S-52X-LI-AC, and S5700S-28P-PWR-LI-AC), S6720LI, S6720S-LI, S5720S-LI, S6720EI, S6720S-EI, S6720HI, S5720EI, S5730HI and S5720HI series switches support only the smart_config.ini format.
  • USB-based deployment using the usbload_config.txt index file can only be performed in a single switch, not a stack of multiple switches. In a stack of multiple switches, if the USB flash drive is connected to the standby switch or a slave switch, the USB-based deployment process will not start. If the USB flash drive is connected to the master switch, the USB indicator blinks red fast, indicating that the USB-based deployment fails. In this case, the switch records an error report including the following information: The usbload_config.txt index file cannot be used for USB deployment of a multi-member stack.
  • In V200R013C00 and later versions, basic stack interface configurations can be delivered for USB-based deployment, and the following commands are included, in cloud management mode.
    1. interface stack-port
    2. port interface enable
    3. shutdown interface
    4. stack slot priority
    5. stack slot renumber
  • In USB-based deployment scenarios, the devices (S5720HI switches) may be upgraded to V200R009C00 or a later version after restart. In this case, the devices check whether the configuration file for next startup contains WLAN configuration that conflicts with the software package for next startup. If so, the devices cannot restart and the USB-based deployment fails. The error report file usbload_error.txt is generated in the root directory of the USB flash drive, which records the failure causes. To solve this problem, you need to use eDesk to convert the configuration file and then set it as the next startup configuration file.

  • The file system format of the USB flash drive must be FAT32, and standard for the USB interface is USB2.0 (USB1.1 interface on the S5700LI). USB flash drives from different vendors differ in model compatibility and drivers. If a USB flash drive cannot be used, try to replace it with another one from a mainstream vendor. Switches support a maximum of 128 GB USB flash drives.

During USB-based deployment

  • Before saving files to a USB flash drive, disable the write-protection function of the USB flash drive.
  • Do not power off the device during a USB-based deployment process. Otherwise, the upgrade fails or the device cannot start.
  • Do not remove the USB flash drive before the USB-based deployment process is complete. Otherwise, data in the USB flash drive may be corrupted.
  • Do not use a partitioned USB flash drive to deploy the S5720EI, S5720HI, S5730HI, S5720SI, S5720I-SI, S6720SI, S6720S-SI, S5720S-SI, S5720LI, S6720HI, S6720LI, S6720S-LI, S5720S-LI, S6720EI, or S6720S-EI switches. Otherwise, the switches may fail to find the files saved on the USB flash drive, resulting in a failed USB-based deployment.
  • The S5700LI supports two index file formats: smart_config.ini and usbload_config.txt. If both types of index files are saved in a USB flash drive, the smart_config.ini file is preferred. During USB-based deployment, it is not recommended to save the two types of index files in the USB flash drive. When rolling back a device to V200R003 or earlier using a USB flash drive, it is recommended to use the usbload_config.txt index file because V200R003 and earlier versions do not support the smart_cfg.ini index file.
  • In a stack system, if one device does not support USB-based deployment, deployment of the entire stack system fails.
  • In USB-based deployment, the deployment may fail because the device configuration is not restored. In this case, you can remove and then install the USB to resolve this problem.
Translation
Download
Updated: 2019-04-04

Document ID: EDOC1100066063

Views: 29693

Downloads: 664

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next