No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R013C00 Configuration Guide - Device Management

This document describes the configurations of Device Management, including device status query, hardware management, Stack, SVF, cloud-based management, PoE, OPS, energy-saving management, information center, fault management, NTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Displaying the Temperature

Displaying the Temperature

Context

If the device temperature is too high or too low, the hardware may be damaged. To learn about the current device temperature, use the following command.

Procedure

  • Run the display temperature { all | slot slot-id } command to view the device temperature.

FAQ

How Can I Determine Whether the Device Temperature Is too High?

The device temperature is too high if high temperature alarm is generated on the device. The system adjusts the fan speed automatically to help ensure that the device temperature is within the normal range.

For details about the device operating temperature , see "Specifications" in the Hardware Description - Chassis.

The following is an example of high temperature alarms:
ENTITYTRAP_1.3.6.1.4.1.2011.5.25.219.2.10.13 hwBrdTempAlarm 140544 
ENTITYTRAP/1/ENTITYBRDTEMPALARM: OID [oid] Temperature rise over or fall below the warning alarm threshold.(Index=[INTEGER], 
ThresholdEntityPhysicalIndex=[INTEGER],EntityPhysicalIndex=[INTEGER], PhysicalName="[OCTET]", EntityThresholdType=[INTEGER],
EntityThresholdValue=[INTEGER],EntityThresholdCurrent=[INTEGER], EntityTrapFaultID=[INTEGER])
SRM_1.3.6.1.4.1.2011.5.25.129.2.2.1 hwTempRisingAlarm  
SRM/3/TEMPRISINGALARM:OID [OID] temperature over major threshold .(EntityPhysicalIndex=[INTEGER], BaseThresholdEntry_entPhys
icalIndex=[INTEGER], BaseThresholdEntry_hwBaseThresholdType=[INTEGER], BaseThresholdEntry_hwBaseThresholdIndex=[INTEGER], Ba
seTrapSeverity=[INTEGER], BaseTrapProbableCause=[INTEGER], BaseTrapEventType=[INTEGER], EntPhysicalName=[OCTET], BaseThresho
ldValue=[INTEGER], BaseThresholdUnit=[INTEGER], BaseThresholdHighWarning=[INTEGER], BaseThresholdHighCritical=[INTEGER])

Why Is a High Temperature Alarm Generated and How Can I Clear It?

Possible Causes
  • Air ventilation around the device is insufficient or obstructed.

  • The ambient temperature of the device is too high.

  • A fan on the device is faulty.

  • The chip temperature is too high.

Troubleshooting Procedure
  1. Clean the air vent and check whether the alarm is cleared.

    (1) If so, go to step 7.

    (2) If not, go to step 2.

  2. Check whether the ambient temperature of the device is too high.

    (1) If so, go to step 3.

    (2) If not, go to step 4.

  3. Lower the temperature in the equipment room, and then go to step 4.

  4. Run the display fan command to check whether any fan is faulty according to the status of fans.

    (1) If so, go to step 6

    (2) If not, go to step 5.

  5. Replace the faulty fan, and then go to step 8.
  6. Run the display temperature all command to view the temperature of he device. Check whether the temperature is high.

    (1) If so, go to step 6.

    (2) If not, go to step 7.

  7. Contact technical support personnel.
Determining Whether a High Temperature Alarm Is Cleared
  1. This alarm is not displayed on the NMS.
  2. This alarm is not displayed when you run the display trapbuffer command to view the trap buffer.
  3. This alarm is not displayed when you run the terminal monitor and terminal trapping commands to view alarm information.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100066159

Views: 26429

Downloads: 3

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next