No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R013C00 Web-based Configuration Guide

This document describes how to configure and maintain devices through the web NMS client, including device status statistics, SVF, interface, Ethernet switching, IP service, IP routing, security, ACL, AAA, system management, QoS, diagnosis service, and EasyDeploy.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a Device as a DHCP Server (Based on an Interface Address Pool)

Example for Configuring a Device as a DHCP Server (Based on an Interface Address Pool)

Networking Requirements

In Figure 9-38, an enterprise divides two network segments for office terminals: 10.1.1.0/24 for employees with fixed office terminals and 10.1.2.0/24 for employees on business trips to temporarily access the network. The enterprise requires that DHCP be used to assign IP addresses to employees with fixed office terminals and employees on business trips. A PC (DHCP Client_1) requires fixed IP address 10.1.1.100/24 to meet service requirements.
Figure 9-38  Networking diagram for configuring the device as a DHCP server

Configuration Roadmap

The configuration roadmap is as follows:

Configure the DHCP server function on the gateway device Switch to dynamically allocate IP addresses to terminals on the two network segments. PCs on the network segment 10.1.1.0/24 are employees' fixed office terminals, and the network segment 10.1.2.0/24 is used by travelling employees to access the network temporarily.

NOTE:

Configure interface link types and VLANs on LSW_1 and LSW_2 to implement Layer 2 communication.

Procedure

  1. Configure the VLANs to which interfaces belong.
    1. Choose Configuration > Basic Services > Interface Settings. Click Connect to PC.
    2. Select GE0/0/1 under Step 2: Select Interface, and set Interface Status and Default VLAN under Step 3: Configure Interface to ON and 10, as shown in Figure 9-39. You do not need to configure other parameters under Step 3: Configure Interface.

      Figure 9-39  Connecting an interface to a PC

    3. Click Apply. In the dialog box that is displayed, click OK.
    4. Configure GE0/0/2 using the same method.
  2. Configure an IP address for each VLANIF interface.
    1. Choose Configuration > Basic Services > VLAN in the navigation tree to open the VLAN configuration page.
    2. Click the VLAN data under VLAN ID to open the Modify VLAN page, select Create VLANIF, and set an appropriate address for IPv4 address, as shown in Figure 9-40.

      Figure 9-40  Configuring a VLANIF interface



    3. Set the parameters and click OK.
  3. Configure an interface address pool.
    1. Choose Configuration > Basic Services > DHCP > DHCP Address Pool.
    2. Set DHCP status to ON to enable the DHCP function.
    3. Click Create. On the Create DHCP Address Pool page, set Address pool type to Interface address pool, select Vlanif10 for Select Interface, and click OK, as shown in Figure 9-41. Repeat the preceding operations to configure an address pool for VLANIF 11.

      Figure 9-41  Configuring an interface address pool



    4. In Address Pool List, select the check box of Vlanif10, and click Display Address Pool. On the Address Pool Information page, select the check box of 10.1.1.100, and click Bind IP. On the Bind IP page, enter 286e-d488-XXXX in the MAC address text box, and click OK, as shown in Figure 9-42.

      Figure 9-42  Statically binding an IP address to a MAC address

Operation Result

Choose Configuration > Basic Services > DHCP and click the data lines of Vlanif10 and Vlanif11 in Address Pool List to view address allocation of interface address pools, as shown in Figure 9-43.

Figure 9-43  Displaying address pool information



Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100066172

Views: 8047

Downloads: 13

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next