No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R013C00 Web-based Configuration Guide

This document describes how to configure and maintain devices through the web NMS client, including device status statistics, SVF, interface, Ethernet switching, IP service, IP routing, security, ACL, AAA, system management, QoS, diagnosis service, and EasyDeploy.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
First Login Through the Web System (Cloud-based Management Mode)

First Login Through the Web System (Cloud-based Management Mode)

Context

First login to a switch in the cloud-based management mode is different from the first login to a switch in the traditional management mode. This section describes how to log in to a switch through the web system for the first time after the device is switched to the cloud-based management mode.

  • For a switch with the ETH management interface, directly connect the PC to the ETH management interface to implement the first login through the web system.
  • For a switch with the MODE button, you can press and hold down the MODE button to implement the first login through the web system.
NOTE:
  • Devices without the MODE button do not support the first login through the web system.

  • First login through the web system, SVF, and EasyDeploy cannot be used together.

Before You Begin

Ensure the following:

  • The switch is powered on.
  • The switch uses the factory settings.

Default Settings

Table 2-5  Default settings for the web system login
Parameter Default Setting
User name admin
Password admin@huawei.com
User level 15
Login IP address 192.168.1.253

Procedure

  1. Connect a PC to the switch.

    NOTE:

    When logging in to a switch through the web system, you are not advised to connect the PC to the switch because any operations performed through the serial interface will cause a failed login for the first time through the web system.

    • Connect the PC to any Ethernet electrical interface of the switch using network cables. Press and hold down the MODE button for 6 seconds or longer. When all indicators on the switch are steady green, the switch enters the initial configuration mode.

    • In the initial configuration mode, the system sets the switch's IP address to 192.168.1.253/24 and the level of the default user admin to 15.

    NOTE:
    • If a switch has been configured when users press and hold down the MODE button for 6 seconds, all indicators blink green fast. In this case, the switch is restored to the normal state after 10 seconds, without affecting the existing configuration.
    • If a switch using factory settings has just started or has been configured through the serial interface when users press and hold down the MODE button for 6 seconds, the switch may fail to enter the initial configuration mode. When all indicators blink fast for 10s, the switch restores to the factory default state.
    • A switch automatically exits the initial configuration mode and restores factory settings if users have not saved the settings after one hour.

  2. Configure an IP address for the PC.

    To ensure that the PC and switch are routable to each other, configure an IP address on the same network segment as the switch's IP address for the PC.

  3. Log in to the switch through the web system.

    Open the web browser on the PC, enter https://192.168.1.253 in the address bar, press Enter, and then the web system login page is displayed, as shown in Figure 2-3.

    NOTE:

    First login to a switch through the web system requires that the browser on the PC must be Microsoft Edge, Internet Explorer 10.0, Internet Explorer 11.0, Firefox 58.0 to Firefox 62.0, or Chrome 60.0 to Chrome 69.0. If the browser version or browser patch version is not within the preceding ranges, the web page may not be properly displayed. Upgrade the browser and browser patch.

    When you log in to the web system for the first time, you must change the password. Only in this way, you can access the main page of the web system.

    Figure 2-3  First login page in the web system
    1. Enter the default user name admin and default password admin@huawei.com, select the language of the web system, click GO or directly press Enter, and the initial configuration page is displayed, as shown in Figure 2-4.
    2. Click apply and save the configurations. After you exit from the initial configuration page, the web system login page is directly displayed. You can log in to the switch again to maintain the switch.

    Figure 2-4  Initialization configuration page
    NOTE:

    On the initial configuration page, select the configuration management mode and click apply. The device automatically configures other management modes.

Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100066172

Views: 7174

Downloads: 11

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next