No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S600-E V200R013C00 Web-based Configuration Guide

This document describes how to configure and maintain devices through the web NMS client, including device status statistics, SVF, interface, Ethernet switching, IP service, IP routing, security, ACL, AAA, system management, QoS, diagnosis service, and EasyDeploy.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
IGMP Snooping

IGMP Snooping

IGMP Snooping Configuration

Context

Configuring basic IGMP snooping functions in a VLAN enables the switch to create and maintain a Layer 2 multicast forwarding table, based on which multicast data packets can be forwarded accurately to receivers over the data link layer.
NOTE:
Multicast flows are considered unknown if they do not match any entry in the multicast forwarding table or if they match multicast forwarding entries with an empty outbound interface list. These flows are not requested by users. The default method that a switch uses to process unknown IPv4 multicast flows depends on whether Layer 2 multicast is enabled and which Layer 2 multicast forwarding mode is used:
  • If Layer 2 multicast is not enabled on a switch, the switch broadcasts unknown multicast flows.
  • If Layer 2 multicast is enabled on a switch, the switch broadcasts unknown multicast flows in a VLAN, regardless of which Layer 2 multicast forwarding mode is used.

Procedure

  1. Choose Configuration > Advanced Services > IGMP Snooping and click the IGMP Snooping Configuration tab.
  2. Click a configuration record of a VLAN enter the editing state, as shown in Figure 5-84.

    Figure 5-84  IGMP Snooping Configuration

  3. Set IGMP snooping parameters, such as IGMP Snooping and IGMP Version.
  4. Click to complete the configuration.

Group Member Ports

Procedure

  • Create a static user.
    1. Choose Configuration > Advanced Services > IGMP Snooping and click the Group Member Ports tab, as shown in Figure 5-85.

      Figure 5-85  Group Member Ports

    2. Click Create Static User to display the Create Static User page, as shown in Figure 5-86.

      Figure 5-86  Create Static User

      Table 5-49 describes parameters on the Create Static User page.
      Table 5-49  Parameters on the Create Static User page

      Parameter

      Description

      Selected outbound interfaces

      Lists the interfaces that you have selected on the panel.

      Multicast group address

      Enter the IP address of the multicast group to which you want to bind the interfaces.

      Multicast source address

      Enter a multicast source address.

      VLAN ID

      Enter the VLAN ID of the interfaces. The value is an integer ranging from 1 to 4094.

    3. Set the parameters.
    4. Click OK.
  • Delete a static user.
    1. Choose Configuration > Advanced Services > IGMP Snooping and click the Group Member Ports tab, as shown in Figure 5-85.
    2. Click Delete Static User to display the Delete Static User page, as shown in Figure 5-87.

      Figure 5-87  Delete Static User

      Table 5-50 describes parameters on the Delete Static User page.
      Table 5-50  Parameters on the Delete Static User page

      Parameter

      Description

      Selected outbound interfaces

      Lists the interfaces that you have selected on the panel.

      VLAN ID

      Select a VLAN ID to remove the interfaces from the group in the specified VLAN.

      Multicast group address

      Enter the IP address of the multicast group from which you want to remove the interfaces.

      Multicast source address

      Enter a multicast source address.

    3. Set the parameters.
    4. Click OK.
  • Delete dynamic multicast entries.
    1. Choose Configuration > Advanced Services > IGMP Snooping and click the Group Member Ports tab, as shown in Figure 5-85.
    2. Select the dynamic multicast entries you want to delete and click Delete Dynamic Multicast Entry. The system asks you whether to delete the entries.
    3. Click OK.
Translation
Download
Updated: 2019-04-08

Document ID: EDOC1100066172

Views: 7307

Downloads: 11

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next