No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Voice Feature Guide 01

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the SIP Value-added Service

Configuring the SIP Value-added Service

The SIP value-added service enriches user experience and brings value-added services for carriers. This section describes how to configure the SIP value-added service.

Configuring the Customized SIP Value-added Service Logic

The SIP value-added service is implemented through the service logic of the system. If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.

Prerequisites

Procedure

  1. In config mode, run the load sip-srvlogic command to load the customized service logic.
  2. In SIP mode, run the if-sip attribute basic srvlogic-index 5 command to make the customized service logic file take effect.

Example

To load the customized service logic file (file name sip_service_logic) on the server whose IP address is 10.13.0.10 through FTP, and make the file effective on the added SIP interface 0, run the following commands:

huawei(config)#load sip-srvlogic ftp 10.13.0.10 sip_service_logic
huawei(config)#interface sip 0
huawei(config-if-sip-0)#if-sip attribute basic srvlogic-index 5

Configuring the Call Waiting Service

The call waiting (CW) service enriches user experience and brings value-added services to carriers. This section describes how to configure the CW service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  3. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the call waiting permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the call waiting permission for a service user.

Example

To configure the CW service for POTS user A with the listed data planning, run the following commands:
  • The CW service code of the POTS user is 5, and the service priority is 1 (the default value is used as an example).
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 5 1
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000 
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 cw enable
To configure the CW service for ISDN user A with the listed data planning, run the following commands:
  • The CW service code of the BRA user is 11, and the service priority is 11 (the default value is used as an example).
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 11 11
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 cw enable

Configuring the Call Hold Service

The call hold (CH) service enriches user experience and brings value-added services to carriers. This section describes how to configure the CH service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  3. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the call hold permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the call hold permission for a service user.

Example

To configure the CH service for POTS user A with the listed data planning, run the following commands:
  • The CH service code of the POTS user is 26, and the service priority is 26 (the default value is used as an example).
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 26 26
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 callhold enable
To configure the CH service for ISDN user A with the listed data planning, run the following commands:
  • The CH service code of the BRA user is 9, and the service priority is 9 (the default value is used as an example).
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 9 9
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 callhold enable

Configuring the Local Three Party Conference Call Service

The local three party conference call (3PTY) service enriches user experience and brings value-added services to carriers. The following describes the procedure for configuring the local 3PTY service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In SIP mode, run the mg-software parameter command to set the 3PTY service mode.
  3. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  4. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the local 3PTY permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the local 3PTY permission for a service user.

Example

To configure the local 3PTY service for POTS user A with the listed data planning, run the following commands:
  • The local 3PTY service code of the POTS user is 1, and the service priority is 5 (the default value is used as an example).
  • The 3PTY service mode: local 3PTY
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 1 5
huawei(config-if-sip-0)#mg-software parameter 28 0
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000 
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 three-party enable
To configure the local 3PTY service for ISDN user A with the listed data planning, run the following commands:
  • The local 3PTY service code of the BRA user is 7, and the service priority is 7 (the default value is used as an example).
  • The 3PTY service mode: local 3PTY
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 7 7
huawei(config-if-sip-0)#mg-software parameter 28 0
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 three-party enable

Configuring the Remote Three Party Conference Call Service

The remote three party conference call (3PTY) service enriches user experience and brings value-added services to carriers. The following describes the procedure for configuring the remote 3PTY service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In SIP mode, run the mg-software parameter command to set the 3PTY service mode.
  3. In SIP mode, run the if-sip attribute optional command to configure the conference factory URI of the SIP interface.
  4. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.

Example

To configure the remote 3PTY service for POTS user A with the listed data planning, run the following commands:
  • The remote 3PTY service code of the POTS user is 21, and the service priority is 21 (the default value is used as an example).
  • The 3PTY service mode: remote 3PTY
  • The conference factory URI of the SIP interface: sip:alice@huawei.com.
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 21 21
huawei(config-if-sip-0)#mg-software parameter 28 1
huawei(config-if-sip-0)#if-sip attribute optional conference-factory-uri sip:alice@huawei.com
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000
To configure the remote 3PTY service for ISDN user A with the listed data planning, run the following commands:
  • The remote 3PTY service code of the BRA user is 23, and the service priority is 23 (the default value is used as an example).
  • The 3PTY service mode: remote 3PTY
  • The conference factory URI of the SIP interface: sip:alice@huawei.com.
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 23 23
huawei(config-if-sip-0)#mg-software parameter 28 1
huawei(config-if-sip-0)#if-sip attribute optional conference-factory-uri sip:alice@huawei.com
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 

Configuring the Conferencing Service

The conferencing service enriches user experience and brings value-added services to carriers. This section describes how to configure the conferencing service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In SIP mode, run the if-sip attribute optional command to configure the conference factory URI of for the SIP interface.
  3. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  4. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the conferencing service permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the conferencing service permission for a service user.

Example

To configure the conferencing service for POTS user A with the listed data planning, run the following commands:
  • The conferencing service code of the POTS user is 0, and the service priority is 4 (the default value is used as an example).
  • The conference factory URI of the SIP interface: sip:alice@huawei.com.
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 0 4
huawei(config-if-sip-0)#if-sip attribute optional conference-factory-uri sip:alice@huawei.com
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 conf enable
To configure the conferencing service for ISDN user A with the listed data planning, run the following commands:
  • The conferencing service code of the BRA user is 6, and the service priority is 6 (the default value is used as an example).
  • The conference factory URI of the SIP interface: sip:alice@huawei.com.
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 6 6
huawei(config-if-sip-0)#if-sip attribute optional conference-factory-uri sip:alice@huawei.com
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 conf enable

Configuring the Explicit Communication Transfer Service

The explicit communication transfer (ECT) service enriches user experience and brings value-added services to carriers. This section describes how to configure the ECT service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  3. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the ECT service permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the ECT service permission for a service user.

Example

To configure the ECT service for POTS user A with the listed data planning, run the following commands:
  • The ECT service code of the POTS user is 2, and the service priority is 3 (the default value is used as an example).
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 2 3
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000 
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 ct enable
To configure the ECT service for ISDN user A with the listed data planning, run the following commands:
  • The ECT service code of the BRA user is 8, and the service priority is 8 (the default value is used as an example).
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 8 8
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 ct enable

Configuring the Call Forwarding Service

The call forwarding service enriches user experience and brings value-added services to carriers. This section describes how to configure the call forwarding service.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority of a POTS user.

    NOTE:
    • This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.
    • The service priority of the ISDN user is configured on the softswitch.

  2. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  3. In the ESL mode, run the sippstnuser servicedata parameter set command to set the forwarded-to number of the POTS phone of the service user.

    NOTE:

    The forwarded-to number of an ISDN user must be registered with the core network.

Example

To configure the call forwarding service for POTS user A with the listed data planning, run the following commands:
  • The call forwarding service code of the POTS user is 17, and the service priority is 17 (the default value is used as an example).
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
  • The call forwarding mode is Call Forwarding Busy (CFB) and the forwarded-to number is 12345678.
huawei(config-if-sip-0)#sipprofile modify srv-pri 17 17
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000
huawei(config-esl-user)#sippstnuser servicedata parameter set 0/2/0 telno 83110000 cfbnum 12345678
To configure the call forwarding service for ISDN user A with the listed data planning, run the following commands:
  • The conferencing service code of the BRA user is 18, and the service priority is 18 (the default value is used as an example).
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 18 18
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010

Configuring the Emergency Call Service

The emergency call service enriches user experience and brings value-added services to carriers. This section describes how to configure the emergency call service.

Procedure

  1. In SIP mode, run the mg-software parameter (sip) command to enable the emergency call permission on the interface.
  2. In config mode, run the local-digitmap add command to configure the emergency digitmap.

Example

To configure the emergency call service on SIP interface 0 (name of the emergency call digitmap: huawei; digitmap body: 110|120|119), run the following commands:

huawei(config)#interface sip 0
hhuawei(config-if-sip-0)#mg-software parameter 6 1
huawei(config-if-sip-0)#quit
huawei(config)#local-digitmap add huawei emergency 110|120|119

Configuring the Hotline Service

The hotline service enriches user experience and brings value-added services to carriers. This section describes how to configure the hotline service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  3. For POTS users, run the sippstnuser servicedata parameter set command in ESL mode to set the hotline number for a service user. For ISDN users, run the sipbrauser servicedata parameter set command to set the hotline number for a service user.
  4. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the hotline service permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the hotline service permission for a service user.

Example

To configure the hotline service for POTS user A with the listed data planning, run the following commands:
  • The hotline service code of the POTS user is 12, and the service priority is 12 (the default value is used as an example).
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
  • The hotline number of user A is 83110001. In addition, set the hotline delay to 0s (immediate hotline mode).
huawei(config-if-sip-0)#sipprofile modify srv-pri 12 12
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000 
huawei(config-esl-user)#sippstnuser servicedata parameter set 0/2/0 telno 83110000 hottime 0 hotlinenum 83110001
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 hotline enable
To configure the hotline service for ISDN user A with the listed data planning, run the following commands:
  • The hotline service code of the BRA user is 13, and the service priority is 13 (the default value is used as an example).
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 8311010.
  • The hotline number of user A is 83110001. The hotline delay to 5s (the default value is used as an example).
huawei(config-if-sip-0)#sipprofile modify srv-pri 13 13
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#sipbrauser servicedata parameter set 0/6/0 telno 83110010 hottime 5 hotlinenum 83110011 
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 hotline enable

Configuring the Message Waiting Indication Service

The Message Waiting Indication (MWI) service enriches user experience and brings value-added services to carriers. This section describes how to configure the MWI service.

Procedure

  1. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  2. For POTS users, run the sippstnuser rightflag set command in ESL mode to set the MWI service permission for a service user. For ISDN users, run the sipbrauser rightflag set command to set the MWI service permission for a service user.

Example

To configure the MWI service for POTS user A with the listed data planning, run the following commands:
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000 
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 mwi enable
To configure the MWI service for ISDN user A with the listed data planning, run the following commands:
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 mwi enable

Configuring the Connected Line Identification Presentation Service

The Connected Line Identification Presentation (COLP) service enriches user experience and brings value-added services to carriers. This section describes how to configure the COLP service.

Procedure

  1. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  2. In SIP mode, run the sipprofile modify command to enable the COLP service on control point PF295.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  3. After the preceding configurations are complete, the service party subscribes to the COLP service on the phone.

Example

To configure the COLP service for POTS user A with the listed data planning, run the following commands:
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000 
huawei(config-esl-user)#quit
huawei(config)#interface sip 0
huawei(config-if-sip-0)#sipprofile modify syspara 295 1
To configure the COLP service for ISDN user A with the listed data planning, run the following commands:
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010 
huawei(config-esl-user)#quit
huawei(config)#interface sip 0
huawei(config-if-sip-0)#sipprofile modify syspara 295 1

Configuring the Malicious Call Identification Service

The malicious call identification (MCID) service enriches user experience and brings value-added services to carriers. This topic describes how to configure the MCID service.

Prerequisites

The following configurations have been completed:

  1. Configuring the Upstream VLAN Interface
  2. Configuring the Media and Signaling IP Address Pools
  3. Adding an SIP Interface
  4. Configuring the Customized SIP Value-added Service Logic
    NOTE:
    • If the preset service logic file cannot meet the requirements, you need to customize and load the customized service logic file. Otherwise, you do not need to customize the service logic file.
    • If the customized service logic file exists, skip this step.

Procedure

  1. In SIP mode, run the sipprofile modify command to set the service priority.

    NOTE:

    This command is used to control the program processing flow inside the system to resolve the adaptation and interworking issues for devices from different vendors. This command is used in the interworking test phase by Huawei engineers. After the interworking test is passed, modification of parameters of this command is not needed in most cases. Incorrect values of parameters of this command may lead to interworking failures. Do not change parameters of this command by yourself. If you need to change parameter values, contact Huawei technical support.

  2. In ESL mode, run the sippstnuser add command to add an SIP PSTN user or run the sipbrauser add command to add an SIP ISDN user.
  3. For POTS users, run the sippstnuser permissionflag set command in ESL mode to set the MCID service permission for a service user. For ISDN users, run the sipbrauser permissionflag set command to set the MCID service permission for a service user.

Example

To configure the MCID service for POTS user A with the listed data planning, run the following commands:
  • The MCID service code of the POTS user is 4, and the service priority is 0 (the default value is used as an example).
  • The ASPB service board is in slot 0/2. The PSTN user A is added to port 0/2/0 on SIP interface 0.
  • The phone number of user A is 83110000.
huawei(config-if-sip-0)#sipprofile modify srv-pri 4 0
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sippstnuser add 0/2/0 0 telno 83110000
huawei(config-esl-user)#sippstnuser rightflag set 0/2/0 telno 83110000 mcid enable
To configure the MCID service for ISDN user A with the listed data planning, run the following commands:
  • The conferencing service code of the ISDN user is 10, and the service priority is 10 (the default value is used as an example).
  • The DSRD service board is in slot 0/6. The BRA user A is added to port 0/6/0 on SIP interface 0.
  • The phone number of user A is 83110010.
huawei(config-if-sip-0)#sipprofile modify srv-pri 10 10
huawei(config-if-sip-0)#quit
huawei(config)#esl user
huawei(config-esl-user)#sipbrauser add 0/6/0 0 telno 83110010
huawei(config-esl-user)#sipbrauser rightflag set 0/6/0 telno 83110010 mcid enable
Translation
Download
Updated: 2019-02-22

Document ID: EDOC1100067358

Views: 13208

Downloads: 129

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next