No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OceanStor 9000 V5 7.0 Parts Replacement 05

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing the PCIe Card on the Riser Card

Replacing the PCIe Card on the Riser Card

On the riser card, the storage node provides the half-height Peripheral Component Interconnect Express (PCIe) card.

Impact on the System

Before replacing a PCIe card, you must power off the storage node. This will adversely affect the services running on the node. Exercise caution when performing this operation.

Prerequisites

  • The replacement PCIe card is ready.
  • The faulty PCIe card has been located.
    NOTE:

    If the PCIe card to be replaced is a half-height card, remove the full-height barrier chip and install it to the PCIe card.

Precaution

  • The storage node supports 2-port GE, 4-port GE, 2-port 10GE, 2-port 25GE RoCE, 2-port 40GE RoCE, and 2-port 100Gb IB PCIe cards. Methods to replace these types of PCIe cards are the same.
  • Only professional technical support engineers are allowed to replace a PCIe card.
  • A storage node has two power modules. Ensure that both are disconnected.
  • If the PCIe card is an IB card or RoCE card, the system automatically checks the firmware version of the new PCIe card after the replacement. If the firmware version does not match the OFED version installed on the device, the system automatically upgrades the firmware of the PCIe card. After the upgrade is complete, the device will restart.

Tools and Materials

  • Phillips screwdrivers
  • Electrostatic discharge (ESD) gloves
  • ESD wrist straps
  • ESD bags
  • Labels

Procedure

  1. Wear an ESD wrist strap or ESD gloves.
  2. Use the KVM to log in to the operating system of the node, enter user name root and its password (default: Root@storage), and run poweroff command to power off the node.

    Wait until the KVM has no output. The power-off is complete.

  3. Remove all power cables and external signal cables.
  4. Remove the storage node from the enclosure.
    1. Loosen the captive screws on the storage node panel using a screwdriver, as shown in step 1 in Figure 3-235.

      Figure 3-235  Pulling out a storage node

    2. Pull out the storage node along the guide rails away from the cabinet, as shown in step 2 in Figure 3-235.
    3. Lever the latches on both sides upwards and remove the storage node in the direction of the arrow by holding the storage node bottom, as shown in Figure 3-236.

      Figure 3-236  Removing the storage node from the holding rails

  5. Remove the enclosure cover.
    1. Use a flat-head screwdriver to loosen the latch that secures the ejector lever of the enclosure cover, as shown in step 1 in Figure 3-237.
    2. Open the ejector lever to push the enclosure cover backwards, as shown in step 2 in Figure 3-237.

      Figure 3-237  Removing an enclosure cover

  6. Loosen the screw on the riser card tray and lift the riser card tray, as shown in Figure 3-238.

    Figure 3-238  Removing a riser card tray

  7. Remove the PCIe card on the riser card.
    1. Horizontally push the latch of the PCIe card outward to unlock it, as shown in step 1 in Figure 3-239.

      Figure 3-239  Removing a PCIe card from a riser card

    2. Rotate the PCIe card latch to open it, as shown in step 2 in Figure 3-239.
    3. Pull out the PCIe card, as shown in step 3 in Figure 3-239.
  8. Put the removed PCIe card into an ESD bag.
  9. Take the replacement PCIe card out of its ESD bag.
  10. Install the PCIe card.
    1. Insert the PCIe card into the PCIe slot, as shown in step 1 in Figure 3-240.

      Figure 3-240  Installing a PCIe card on a riser card

    2. Close the latch, as shown in step 2 in Figure 3-240.
  11. Install the riser card tray and tighten the screw, as shown in Figure 3-241.

    Figure 3-241  Installing a riser card tray

  12. Install the enclosure cover.
    1. Place the enclosure cover horizontally, align it with the fixing slots on both side panels of the enclosure, and close the ejector lever, as shown in steps 1 and 2 in Figure 3-242.
    2. Use a flat-head screwdriver to tighten the latch in order to secure the ejector lever of the enclosure cover, as shown in step 3 in Figure 3-242.

      Figure 3-242  Installing an enclosure cover

  13. Put the storage node into the cabinet.
    1. Pull out the inner rails as far as they will go, as shown in Figure 3-243.

      Figure 3-243  Pulling out an inner rail

    2. Align the screws on the storage node with the notches on the inner guide rails, push the storage node inwards until you hear a sound, and ensure that the latches eject and completely block the screws to affix the storage node to the inner guide rails, as shown in Figure 3-244.

      Figure 3-244  Installing a storage node

    3. Press the release buttons on both sides and push the storage node into the cabinet along the holding rails, as shown in steps 1 and 2 in Figure 3-245.

      Figure 3-245  Pushing the server into the cabinet along the holding rails

    4. Optional: Tighten the captive screws on the mounting ears to secure the storage node, as shown in Figure 3-246.

      Figure 3-246  Securing the storage node

  14. Connect the storage node to the power sockets and peripheral devices according to the cable connection labels. Then power on the storage node.
  15. Log in to the storage node using the KVM.
  16. Clear NVDIMM data.
    1. When the screen shown in Figure 3-247 is displayed during the system startup, press Delete.

      Figure 3-247  BIOS startup page

      NOTE:
      If a dialog box that informs you of entering the password is displayed, enter the BIOS password (default: Admin@9000).

    2. Choose Security > Clear NvDimm Flash and press Enter, as shown in Figure 3-248.

      Figure 3-248  Choosing Clear NvDimm Flash

    3. In the Clear NvDimm Flash dialog box, select Yes and press Enter, as shown in Figure 3-249.

      Figure 3-249  Starting to clear NVDIMM data

    4. If the Clear NvDimm flash success! message is displayed, data in the NVDIMM is cleared, as shown in Figure 3-250.

      Figure 3-250  NVDIMM data cleared

    5. Press Enter and then F10. In the dialog box that is displayed, select Yes and press Enter to save the configuration and restart the storage node, as shown in Figure 3-251.

      Figure 3-251  Saving the configuration and restarting the storage node

  17. Log in to the WebUI of the iBMC storage node, and choose Information > System Info > Other Devices to query the information about corresponding components and check whether the replacement succeeds.

    • If the PCIe card is displayed on the iBMC page, the PCIe card is successfully installed.
    • If the PCIe card is not displayed on the iBMC page, the replacement PCIe card may not be properly installed. You need to reperform 2 to 17. If there is still no information about the PCIe card, contact Huawei technical support.

Follow-up Procedure

After replacing the PCIe card, label the replaced PCIe card to facilitate subsequent operations.

Download
Updated: 2019-07-25

Document ID: EDOC1100067965

Views: 11982

Downloads: 11

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next