No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OceanStor 9000 V5 7.0 Parts Replacement 05

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Replacing the Li&Mn Battery

Replacing the Li&Mn Battery

Impact on the System

  • Before replacing the Li&Mn battery, you must power off the P36E or C36E node. This will adversely affect the services running on the node. Exercise caution when performing this operation.

Prerequisites

  • The replacement Li&Mn battery is ready.
  • You have recorded the cable mapping of the device, securely stopped the services, executed a shut-down command in the operating system to power off the P36E or C36E node, and disconnected the node from power sockets and peripheral devices.

Tools and Materials

  • Flat-head screwdrivers
  • Phillips screwdrivers
  • ESD gloves
  • ESD wrist straps
  • ESD bags
  • Labels

Procedure

  1. Wear an ESD wrist strap or ESD gloves.
  2. Use the KVM to log in to the operating system of the node, enter user name root and its password (default: Root@storage), and run poweroff command to power off the node.

    Wait until the KVM has no output. The power-off is complete.

  3. Remove all power cables and external signal cables.
  4. Remove the storage node from the cabinet.
    1. Loosen the captive screws on the panel using a Phillips screwdriver, as shown in step 1 in Figure 4-151.

      Figure 4-151  Removing a storage node

    2. Slowly pull the storage node out along the guide rails, as shown in step 2 in Figure 4-151.
    3. Press the release buttons on both sides and pull the storage node out of the cabinet along the guide rails, as shown in step 3 in Figure 4-151.
  5. Remove the enclosure cover.
    1. Use a flat-head screwdriver to loosen the latch that secures the ejector lever of the enclosure cover, as shown in step 1 in Figure 4-152.
    2. Open the ejector lever to push the enclosure cover backward, as shown in step 2 in Figure 4-152.

      Figure 4-152  Removing an enclosure cover

  6. Remove the Li&Mn battery.
    1. Pull up the right end of the battery and remove it from the slot. See Figure 4-153.

      Figure 4-153  Removing the Li&Mn battery

  7. Place the removed Li&Mn battery in an ESD bag.
  8. Take the spare Li&Mn battery out of its ESD bag.
  9. Install the Li&Mn battery.
    1. Hold the battery with the side marked with text facing upwards, insert the left end of the battery into the slot, and gently press down the battery until it is properly installed in the slot. See Figure 4-154.

      Figure 4-154  Installing the Li&Mn battery

  10. Install the enclosure cover.
    1. Place the enclosure cover horizontally, align it with the fixing slots on both side panels of the enclosure, and close the ejector lever, as shown in steps 1 and 2 in Figure 4-155.

      Figure 4-155  Installing an enclosure cover

    2. Tighten the latch to secure the ejector lever of the enclosure cover using flat-head screwdriver, as shown in step 3 in Figure 4-155.
  11. Put the storage node into the cabinet.
    1. Arrange at least four persons to lift the storage node on both sides, align the inner rails on the storage node with the holding rails, and push the storage node into the cabinet along the holding rails, as shown in Figure 4-156.

      Figure 4-156  Pushing a storage node into holding rails

    2. Press the release buttons on both sides, and push the storage node into the cabinet until the storage node cannot move forward, as shown in Figure 4-157.

      Figure 4-157  Pushing a storage node into a cabinet

    3. Tighten the two captive screws on the mounting ears to secure the storage node, as shown in Figure 4-158.

      Figure 4-158  Securing a storage node

  12. Connect the storage node to the power sockets and peripheral devices according to the cable connection labels. Then power on the storage node.
  13. Inspect the system using SmartKit. Choose Home > Storage > Routine Maintenance > More > Inspection to check the system status. For details, see the OceanStor 9000 V5 Routine Maintenance.

    • If all inspection items are successful: The inspection is successful.
    • If some inspection items fail the inspection: The inspection is failed. Rectify the faults by taking recommended actions in the inspection reports. You need to reperform inspection after rectifying. If the inspection is still failed, contact Huawei technical support.

Follow-up Procedure

After replacing the Li&Mn battery, label the replaced Li&Mn battery to facilitate subsequent operations.

Download
Updated: 2019-07-25

Document ID: EDOC1100067965

Views: 12279

Downloads: 11

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next