Purpose
This document describes how to use SmartKit to Site Deployment Delivery, Routine Maintenance, Troubleshooting and Upgrade/Patch Installation.
Intended Audience
This document is intended for:
- Technical support personnel
- Maintenance personnel
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
|
Description
|
|---|
![]()
|
Indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
|
![]()
|
Indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
|
![]()
|
Indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
|
![]()
|
Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal injury.
|
![]()
|
Supplements the important information in the main text.
NOTE is used to address information not related to personal injury, equipment damage, and environment deterioration.
|
Change History
Changes between document issues are cumulative. The latest document issue contains all the changes made in earlier issues.
Issue
|
Date
|
Description
|
|---|
14
|
2021-01-15
|
This issue is the fourteenth official release.
|
13
|
2020-11-30
|
This issue is the thirteenth official release.
- Updated the inspection item list in health check.
- Added the .
- Optimized the procedure and descriptions of some functions.
|
12
|
2020-11-06
|
This issue is the twelfth official release.
- Added the following sections:
- Updated the compatibility lists of all functions.
- Added the SNMPv3 encryption password parameter to the Add Device page.
- Updated the OS compatibility list and inspection item list in health check.
- Updated the Linux OS log collection item list.
- Optimized the procedure and descriptions of some functions.
|
11
|
2020-07-24
|
Optimized some description.
|
10
|
2020-07-13
|
- Optimized some procedures and description.
- Updated the compatibility lists of all functions.
- Added the description of parameters related to IES servers in some functions.
- Added the content of "TCE Custom Log Collection" in log collection.
- Supported the function of setting the number of concurrent tasks in health check.
- Added the Configuring IES function.
- Added SNMP and IPMI Troubleshooting Methods in FAQ.
- Added Progress Bar Is Stuck at 50% During the Upgrade of the PCIe Card and Hard Disk in Upgrading PCIe Card and Hard Disk Firmware.
|
09
|
2020-04-17
|
- Optimized some procedures and figures.
- Updated the compatibility lists of all functions.
- Added the method of upgrading the SP by setting up the CIFS/NFS service to firmware upgrade.
- Added the TaiShan 100 mounting mode to RAID configuration.
- Added the intelligent speed adjustment function to iBMC configuration.
- Supported IES devices in health check and log collection.
|
08
|
2020-02-21
|
- Optimized some procedures and figures.
- Updated the compatibility lists of all functions.
|
07
|
2019-11-18
|
- Optimized some procedures and description.
- Added the methods of installing and upgrading subtool scenarios.
- Updated the compatibility lists of all functions.
- Added the troubleshooting of abnormal watchdog on the OS to firmware upgrade.
- Added the description of intermediate versions to firmware upgrade and E9000 upgrade.
- Added the TaiShan servers to PCIe card and hard disk firmware upgrade.
|
06
|
2019-09-12
|
- Optimized some procedures and figures.
- Added the description of sevice repair.
- Updated the compatibility lists of all functions.
- Added the SNMP Configuration Error guide.
- Added the guide for collecting the OS logs of a single server to log collection.
|
05
|
2019-08-06
|
- Optimized the description.
- Added the data collection service setting function in the iBMC configuration.
|
04
|
2019-06-05
|
- Optimized some procedures and figures.
- Added some supported models to compatibility lists of some functions.
|
03
|
2019-04-30
|
- Added screenshots of operation procedures.
- Optimized the description.
|
02
|
2019-04-03
|
- Supported image mounting on a KunLun server.
- Supported burn-in tests for V5 servers.
- Supported drive firmware version check during inspection.
- Supported log collection for ES3000 V5 servers.
- Supported the synchronization from HostName to SysName in the iBMC configuration.
|
01
|
2019-03-01
|
- This issue is the first official release.
|
