USG6555E
Overview
| Description | Part Number | Model | First supported version |
|---|---|---|---|
| USG6555E AC Host (2*GE WAN+8*GE Combo+2*10GE SFP+,1 AC power) | 02353AEK | USG6555E-AC | V600R007C00 |
| USG6555E AC Host(2*GE WAN+8*GE Combo+2*10GE SFP+,1 AC power) | 02353AEK-001 | USG6555E-AC | V600R007C20SPC500 |
| USG6555E AC Host(2*GE WAN+8*GE Combo+2*10GE SFP+,1 AC power) | 02353AEK-004 | USG6555E-AC | V600R007C20SPC600 |
Appearance
The two USB ports of earlier-delivered models are USB 3.0 and USB 2.0 respectively, whereas those of later-delivered models are both USB 2.0. In this document, earlier-delivered models are used as examples.
Components
1. Product series ID |
2. Indicator and button area |
3. Fixed interface area |
4. Protective ground terminal |
5. MAC label |
6. SN label |
7. Fan module |
8. Optional power module slot |
9. Power module |
- |
Name |
Description |
|---|---|
Product series ID |
Indicates the product series of the device. For details about the product model, see the nameplate in the lower part of the device. |
Indicator and button area |
Provides multiple indicators to display the running status of the device in real time and provides the RST button for emergency maintenance. |
Fixed interface area |
Provides service ports, USB ports, console ports, and out-of-band management ports for device configuration and maintenance. |
Protective ground terminal |
Connects the M4 OT terminal of a PGND cable to the cabinet or the ground bar in the equipment room. |
MAC label |
Uniquely identifies the MAC address of the device, which is required during network forwarding configuration. |
SN label |
Uniquely identifies the device, which needs to be provided for the local technical support personnel to apply for a license. |
Fan module |
Dissipates heat for the device and is swappable. The fan module can be removed for no more than 1 minute. The slot number of the fan module is 4. |
Power module |
Provides power input and distribution for the device. One power module is included in the standard configuration. Two power modules can be configured to achieve 1+1 power redundancy. When one power module is running properly, the other one is hot swappable. The silkscreens of the power module slots are PWR1 and PWR2, and the corresponding slot numbers are 2 and 3 respectively. |
Indicators and Buttons
1. PWR, SYS, USB, HA, WAN and CLOUD indicators |
2. GE electrical port ACT indicator |
3. GE electrical port LINK indicator |
4. Optical port ACT indicator |
5. Optical port LINK indicator |
6. MGMT port indicator |
7. RST button |
- |
- |
- |
Arrowheads of optical ports show the positions of the ports. A down arrowhead indicates a port in the upper part, and an up arrowhead indicates a port in the lower part.
| Silkscreen | Name | Color | Status | Description |
|---|---|---|---|---|
| PWR | Power indicator | Green | Steady on | The power module is working properly. |
| - | Off | The power module is faulty or the device is not powered on. | ||
| SYS | SYS indicator | Green | Steady on | The system is being powered on or restarted. |
| Green | Blinks once every 2 seconds (0.5 Hz). | The system is running normally. | ||
| Green | Blinking four times every second (4 Hz) | The system is starting. | ||
| Red | Steady on |
NOTE:
If the system starts with two power modules and one power module is not powered on, the SYS indicator is steady red, but the system is running properly. |
||
| - | Off | The system is not running. | ||
| USB | USB indicator | Green | Steady on | USB-based deployment has been completed. |
| Green | Blinking four times every second (4 Hz) | The system is reading data from the USB flash drive. | ||
| Red | Steady on | USB-based deployment fails. | ||
| - | Off | USB-based deployment is disabled (default state). | ||
| HA | HA indicator | Green | Steady on | Hot backup, managing the master device |
| Green | Blinks once every 2 seconds (0.5 Hz). | Hot backup, managing the slave device | ||
| Red | Steady on | Dual-system hot backup is faulty. | ||
| - | Off | The dual-system hot backup function is disabled. | ||
| WAN | WAN indicator | - | Off | Reserved function. This function is not enabled. |
| CLOUD | CLOUD indicator | Green | Steady on | Connected to the cloud management platform. |
| Green | Blinking four times every second (4 Hz) | Connecting to the cloud management platform, transmitting or receiving data. | ||
| - | Off | The device is not connected to the cloud management platform. | ||
| - | ACT indicator of the GE electrical port | Yellow | Blinking (12 Hz) | The port is sending or receiving data. |
| - | Off | The port is not sending or receiving data. | ||
| - | LINK indicator of the GE electrical ports | Green | Steady on | The port link is connected. |
| - | Off | No link is established on the port. | ||
| - | LINK indicator of the optical port | Yellow | Blinking (12 Hz) | The port is sending or receiving data. |
| - | Off | The port is not sending or receiving data. | ||
| - | LINK indicator of an optical port | Green | Steady on | The port link is connected. |
| - | Off | No link is established on the port. | ||
| - | MGMT port indicator | Green | Steady on | The port link is connected. |
| Green | Blinking (12 Hz) | The port is sending or receiving data. | ||
| - | Off | No link is established on the port. |
| Silkscreen | Name | Description |
|---|---|---|
| RST | RST button | To restart the device, press the RST button. Ensure that the running configuration is saved before pressing the RST button. This button can enable you to restore the default settings with one click. To be specific, you can hold down the RST button for 5 seconds and then release it to restore the default settings and restart the device. |
Ports
1. Combo port |
2. 10GE optical port |
3. WAN port |
4. SSD card slot |
5. USB 3.0 port or USB0 NOTE:
|
6. USB 2.0 port or USB1 NOTE:
|
7. Console port |
8. MGMT port |
- |
- |
| Port | Connector Type | Description | Available Components |
|---|---|---|---|
| Combo ports (0 to 7) | RJ45 + SFP | Combo ports. Combo ports are logic ports. One combo port can work as a GE electrical interface or a GE optical port. Each combo port has only one internal forwarding port. When the electrical port is enabled, the optical port is disabled. When the optical port is enabled, the electrical port is disabled. The electrical and optical ports of a combo port use the same interface view, numbered from GigabitEthernet 0/0/0 to GigabitEthernet 0/0/7. By default, the combo port is used as an electrical port. You can use the combo enable { copper | fiber } command to set the working mode of combo ports according to network requirements. NOTE:
Arrowheads show the positions of ports. A down arrowhead indicates a port at the bottom, and an up arrowhead indicates a port at the top. |
NOTE:
In V600R007C20SPC500 and later versions, Combo ports support 100Mbps SFP Optical Modules. |
| 10GE optical ports (0 to 1) | SFP+ | 2 10GE optical ports, numbered from XGigabitEthernet 0/0/0 to XGigabitEthernet 0/0/1. NOTE:
In V600R007C20 and later versions, 10GE optical ports support 1Gbps SFP Copper Modules and 1Gbps eSFP Optical Modules. By default, the rate of 10GE optical ports are 10GE. You can run the set device port-config-mode [ 10ge | ge ] command to set the rate of 10GE optical ports are to 10GE or GE as required. |
|
| WAN ports (0 to 1) | RJ45 | 2 10/100/1000M autosensing Ethernet electrical ports, numbered from WAN 0/0/0 to WAN 0/0/1. The device is connected to the WAN or cloud management center using a network cable. |
|
| SSD card slot | - | The M.2 module is inserted to record logs and reports in real time. The M.2 module is optional. You can purchase the M.2 module as required. | |
| USB 3.0 port or USB0 | USB Type A | USB port allows you to insert an USB flash drive for system software upgrades. For details on upgrades through USB flash drives, refer to the Upgrade Guide delivered with the device. | USB flash drive |
| USB 2.0 port or USB1 | USB Type A | USB ports allow you to insert USB devices for system software upgrades. For details on upgrades through USB devices, refer to the Upgrade Guide delivered with the device. | USB flash drive |
| Console port | RJ45 | Console ports allow you to locally connect a PC to the device. You can use a console cable to connect the console port (RJ45) on the device to the COM port on your PC and use a serial port terminal program on your PC to access, configure, and manage the device. |
|
| MGMT port | RJ45 | Out-of-band 10/100/1000M RJ45 autosensing Ethernet management port. The interface number is METH 0/0/0 and the default IP address of the interface is 192.168.0.1. You can connect this port to the network port or any reachable port on a PC through a network cable. Then, you can use Telnet to access the CLI or use a web browser to access the web UI to configure, manage, and maintain the device. NOTE:
The MGMT port cannot be used as a service port. |
Power Supply System
- Early delivery: The power supply system has one PAC60S12-AR, PAC60S12-R, or PAC600S12-CB AC power module. Two power modules can be configured for 1+1 power redundancy.
- Later delivery: The power supply system has one PAC60S12-AR AC power module. Two power modules can be configured for 1+1 power redundancy.
Heat Dissipation System
The heat dissipation system uses one FAN-023A-B module to dissipate heat for the system. From the front panel, the device provides a front-to-rear air flow. The fan module locates at the air exhaust of the system.
Technical Specifications
| Item | Specification |
|---|---|
| Installation Type |
|
| Cabinet installation standard | Cabinet with a depth of 600 mm or above |
| Dimensions without packaging (H x W x D) [mm(in.)] | 43.6 mm x 442 mm x 420 mm (1.72 in. x 17.4 in. x 16.54 in.) |
| Dimensions with packaging (H x W x D) [mm(in.)] | 220 mm x 550 mm x 530 mm (8.66 in. x 21.65 in. x 20.87 in.) |
| Chassis height [U] | 1 U |
| Weight with packaging [kg(lb)] |
|
| Weight without packaging [kg(lb)] |
|
| CPU | 1 CPU, 4 cores/CPU, up to 1.4 GHz |
| Memory | DDR4 4 GB |
| NOR Flash |
|
| NAND Flash | 2 GB |
| Hard disk | Optional. M.2 SSD (240GB), hot-swappable. |
| Console port | RJ45 |
| Eth Management port | RJ45 |
| Maximum power consumption [W] |
|
| Maximum heat dissipation [BTU/hour] |
|
| MTBF [years] | 68.98 years |
| MTTR [hours] | 2 hours |
| Power supply mode | AC built-in |
| Number of power modules | 1 |
| Rated input voltage [V] | 100 V to 240 V, 50 Hz/60 Hz |
| Input voltage range [V] | 90 V to 290 V, 47 Hz to 63 Hz |
| Types of fans | Pluggable |
| Number of fan modules | 1 |
| Heat dissipation mode | The fan module locates at the air exhaust of the system. |
| Airflow direction | Air inlet from front and air outlet from rear |
| Redundant power supply | Two power modules are supported for 1+1 power redundancy. |
| Long-term operating temperature [°C(°F)] | 0°C to 45°C |
| Storage temperature [°C(°F)] | -40°C to 70°C |
| Long-term operating relative humidity [RH] | 5% RH to 95% RH, non-condensing |
| Storage relative humidity [RH] | 5% RH to 95% RH, non-condensing |
| Long-term operating altitude [m(ft.)] | 0 m to 5000 m |
| Storage altitude [m(ft.)] | 0 m to 5000 m |
- The width does not include the size of mounting ears.
- The height is 1U (1U = 1.75 inches, or about 44.45 mm), which is a height unit defined in International Electrotechnical Commission (IEC) 60297 standards.
- Temperature and humidity are measured 1.5 m above the floor and 0.4 m in front of the rack when no protection plate exists before or after the rack.