No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - Interface Management

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples of the interfaces supported by the device.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring an ADSL Interface

Example for Configuring an ADSL Interface

Networking Requirements

As shown in Figure 16-2, multiple hosts in Enterprise A access an enterprise gateway router. The router accesses a DSLAM over an ADSL line.

Enterprise A requires a data access solution that is easy to deploy and provides high-speed downstream transmission to meet requirements of data and video services. To meet these service requirements, the carrier provides an ADSL line for Enterprise A so that the device can connect to the DSLAM by using an ADSL interface.

Figure 16-2  ADSL networking diagram

Configuration Roadmap

The configuration roadmap is as follows:
  1. Deactivate an ADSL interface.
  2. Set the same parameters on the device as those of the DSLAM. Parameters for the ADSL interface on the DSLAM: The transmission standard ADSL2+ is used, bit exchange and trellis coding are enabled, and seamless rate adaptation are disabled.
  3. Activate the ADSL interface.

Procedure

  1. Deactivate ATM1/0/0.

    <Huawei> system-view
    [Huawei] sysname Router
    [Router] interface atm 1/0/0
    [Router-Atm1/0/0] shutdown

  2. Configure the transmission standard ADSL2+ for the ADSL interface.

    [Router-Atm1/0/0] adsl standard adsl2+

  3. Enable bit exchange on the ADSL interface.

    [Router-Atm1/0/0] adsl bitswap on

  4. Disable seamless rate adaptation on the ADSL interface.

    [Router-Atm1/0/0] adsl sra off

  5. Enable trellis coding on the ADSL interface.

    [Router-Atm1/0/0] adsl trellis on

  6. Activate ATM1/0/0.

    [Router-Atm1/0/0] undo shutdown
    [Router-Atm1/0/0] quit

  7. Verify the configuration.

    # Check the training status, transmission standard, line status, performance statistics, bit exchange status, seamless rate adaptation status, trellis coding status, and board version of the ADSL interface.

    [Router] display dsl interface atm 1/0/0
     --------------------------------------------------------------
     DSL driver and PHY status
          Training Status                      : Showtime
          Transmission mode                    : ADSL2+
          Line Status                          : No Defect
          Downstream max. attainable rate(Kbps): 8184
          Upstream max. attainable rate(Kbps)  : 529
          Downstream actual net data rate(Kbps): 4538
          Upstream actual net data rate(Kbps)  : 221
          Downstream SNR margin(dB)            : 13.1
          Upstream SNR margin(dB)              : 18.9
          Downstream attenuation(dB)           : 0.0
          Upstream attenuation(dB)             : 4.8
          Downstream output power(dB)          : 7.2
          Upstream output power(dB)            : -8.3
          Downstream total cells               : 3305378
          Upstream total cells                 : 74443
          Downstream data cells                : 36545
          Upstream data cells                  : 5447
          Downstream bit errors                : 124
          Upstream bit errors                  : 365
          Total drop cells                     : 241
          Downstream total ES count            : 0
          Upstream total ES count              : 0
          Downstream total SES count           : 0
          Upstream total SES count             : 0
          Downstream total UAS count           : 72
          Upstream total UAS count             : 72
          Total AS count                       : 36
    
     Line modulations
          G.Dmt                                : Disabled
          ADSL2                                : Disabled
          T1.413                               : Disabled
          AnnexL                               : Disabled
          ADSL2+                               : Enabled
          AnnexM                               : Disabled
    
     Line capability
          Bitswap                              : On
          SRA                                  : Off
          Trellis coding                       : On
    
     Board version
          vendor ID                            : BDCM:0x938f                                                         
          vendor serial                        : 0x938f  
          Board ID:                            : 963281TAN
          Software version                     : 4.06L.03
          Bootloader (CFE) version             : 1.0.37-106.24
          DSL PHY and driver version           : A2pD033a.d23c
          Build timestamp                      : 20110221_2122
     --------------------------------------------------------------

    # Check the configuration and status of an ADSL interface.

    [Router] display interface atm 1/0/0
    Atm1/0/0 current state : UP
    Line protocol current state : UP
    Last line protocol up time : 2011-7-27 14:57:48
    Description:HUAWEI, AR Series, Atm1/0/0 Interface
    Route Port,The Maximum Transmit Unit is 1488
    Internet Address is 1.1.1.1/24
    AAL enabled: AAL5, Maximum VCs: 16
    VCs on main-interface: 1 (Total VCs: 1)
    VPs on main-interface: 0 (Total VPs: 0)
    Last physical up time   : 2010-06-21 14:56:32
    Last physical down time : 2010-06-21 14:56:31
    Current system time: 2011-08-01 15:42:04
    
    Port PHY type    : ADSL
    The physical uptimes since the system startup : 2
    Last 300 seconds input rate 0 bits/sec, 0 packets/sec
    Last 300 seconds output rate 0 bits/sec, 0 packets/sec
    
    Input correct packet:  0 packets, Input total data:  0 bytes
      OAM Cells:                  0,  ASM Cells:                   0
      Packet Errors:              0,  Cell Errors:                 0
    
    Output:  0 packets, 0 bytes
      OAM Cells:                  0,  ASM Cells:                   0
    
        Input bandwidth utilization  :    0%
        Output bandwidth utilization :    0%       

Configuration Files

  • Configuration file of the Router
    #
     sysname Router
    #
    interface Atm1/0/0
     adsl standard adsl2+
    #
    return
Translation
Download
Updated: 2019-03-06

Document ID: EDOC1100069331

Views: 20999

Downloads: 93

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next