No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - Interface Management

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples of the interfaces supported by the device.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring CPOS Interfaces to Converge E1 Lines

Example for Configuring CPOS Interfaces to Converge E1 Lines

Networking Requirements

As shown in Figure 15-11, RouterA connects to seven Routers B through H. Each of the seven Routers connects to RouterA using an E1 link. RouterA uses a CPOS interface to aggregate these E1 links.

When another E1 link is added to RouterB to provide more bandwidth, the two E1 links need to be bound using MP-Group interfaces.

The requirements on RouterA are as follows:
  • RouterA uses the clock signals transmitted from the SDH network.
  • The RouterA's CPOS interface uses SDH as the frame format, and the AUG multiplexing mode is au-4.
Figure 15-11  Networking diagram for configuring CPOS interfaces to converge E1 lines

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure line attributes, including clock mode, frame format, and AUG multiplexing mode, on RouterA's CPOS interface.
    NOTE:

    By default, the clock mode is slave clock, frame format is SDH, and AUG multiplexing mode is au-4. The default line attributes on CPOS interface do not need to be modified in this example.

  2. Create and configure an MP-Group interface on RouterA and RouterB.
  3. Configure an E1 channel on the CPOS interface of RouterA and bind the E1 channel to the MP-Group interface.
  4. Bind the E1-F interface to the MP-Group interface on RouterB.

Procedure

  1. Create and configure an MP-Group interface on RouterA.

    <Huawei> system-view
    [Huawei] sysname RouterA
    [RouterA] interface mp-group 0/0/1
    [RouterA-Mp-group0/0/1] ip address 10.10.10.1 24
    [RouterA-Mp-group0/0/1] quit

  2. Configure an E1 channel for a CPOS interface.

    [RouterA] controller cpos 1/0/0
    [RouterA-Cpos1/0/0] e1 1 unframed
    [RouterA-Cpos1/0/0] e1 2 unframed
    [RouterA-Cpos1/0/0] quit

  3. Bind the E1 channel to the MP-Group interface.

    [RouterA] interface serial 1/0/0/1:0
    [RouterA-Serial1/0/0/1:0] ppp mp mp-group 0/0/1
    [RouterA-Serial1/0/0/1:0] quit
    [RouterA] interface serial 1/0/0/2:0
    [RouterA-Serial1/0/0/2:0] ppp mp mp-group 0/0/1
    [RouterA-Serial1/0/0/2:0] quit

  4. Create and configure an MP-Group interface on RouterB.

    <Huawei> system-view
    [Huawei] sysname RouterB
    [RouterB] interface mp-group 0/0/1
    [RouterB-Mp-group0/0/1] ip address 10.10.10.2 24
    [RouterB-Mp-group0/0/1] quit

  5. Bind the E1-F interface to the MP-Group interface on RouterB.

    [RouterB] interface serial 1/0/0
    [RouterB-Serial1/0/0] fe1 unframed
    [RouterB-Serial1/0/0] ppp mp mp-group 0/0/1
    [RouterB-Serial1/0/0] quit
    [RouterB] interface serial 2/0/0
    [RouterB-Serial2/0/0] fe1 unframed
    [RouterB-Serial2/0/0] ppp mp mp-group 0/0/1
    [RouterB-Serial2/0/0] quit

  6. Verify the configuration.

    # View information about E1 channel 1 on CPOS 1/0/0.

    [RouterA] display controller cpos 1/0/0 e1 1
    Cpos1/0/0 current state : UP
    Description : HUAWEI, AR Series, Cpos1/0/0 Interface
      Frame-format SDH, multiplex AU-4, clock slave, loopback not set
      Tx: J0: 0x1, J1: NULL, C2: 0x2
      Rx: J0: NULL, J1: NULL, C2: 0x0
    Regenerator section:
      Alarm: none
      Error: 0 BIP
    Multiplex section:
      Alarm: none
      Error: 0 BIP, 0 REI
    Higher order path(VC-4-1):
      Alarm: none
      Error: 0 BIP, 0 REI
    Lower order path:
      Alarm: none
      Error: 0 BIP, 0 REI
    Cpos1/0/0  CE1 1 is up
      Frame-format NO-CRC4, clock slave, loopback not set
    E1 framer(1-1-1-1):
      Alarm: none
      Error: 0 CEC, 0 FEBC, 0 REC  

    # View information about the MP-Group interface on RouterA.

    [RouterA] display interface mp-group
    Mp-group0/0/1 current state : UP
    Line protocol current state : UP
    Last line protocol up time : 2011-06-09 10:20:36
    Description:HUAWEI, AR Series, Mp-group0/0/1 Interface
    Route Port,The Maximum Transmit Unit is 1500
    Internet Address is 10.10.10.1/24
    Link layer protocol is PPP
    LCP opened, MP opened, IPCP opened
    Physical is MP, baudrate is 64000 bps
    Current system time: 2011-02-09 10:21:48
        Last 300 seconds input rate 0 bytes/sec, 0 packets/sec
        Last 300 seconds output rate 0 bytes/sec, 0 packets/sec
        Realtime 0 seconds input rate 0 bytes/sec, 0 packets/sec
        Realtime 0 seconds output rate 0 bytes/sec, 0 packets/sec
        6 packets input, 84 bytes, 0 drops
        6 packets output, 84 bytes, 0 drops
        Input bandwidth utilization  : 0.00%
        Output bandwidth utilization : 0.00% 

    # Check the network connectivity.

    [RouterA] ping 10.10.10.2
      PING 10.10.10.2: 56 data bytes, press CTRL_C to break
        Reply from 10.10.10.2: bytes=56 Sequence=1 ttl=255 time=14 ms
        Reply from 10.10.10.2: bytes=56 Sequence=2 ttl=255 time=4 ms
        Reply from 10.10.10.2: bytes=56 Sequence=3 ttl=255 time=4 ms
        Reply from 10.10.10.2: bytes=56 Sequence=4 ttl=255 time=4 ms
        Reply from 10.10.10.2: bytes=56 Sequence=5 ttl=255 time=4 ms
    
      --- 10.10.10.2 ping statistics ---
        5 packet(s) transmitted
        5 packet(s) received
        0.00% packet loss
        round-trip min/avg/max = 4/6/14 ms 

Configuration Files

  • Configuration file of RouterA
    #
     sysname RouterA
    #
    interface Mp-group0/0/1
     ip address 10.10.10.1 24
    #
    controller cpos 1/0/0
     e1 1 unframed
     e1 2 unframed
    #
    interface Serial1/0/0/1:0
     link-protocol ppp
     ppp mp mp-group 0/0/1
    #
    interface Serial1/0/0/2:0
     link-protocol ppp
     ppp mp mp-group 0/0/1
    #
    return
  • Configuration file of RouterB
    #
     sysname RouterB
    #
    interface Mp-group0/0/1
     ip address 10.10.10.2 24
    #
    interface Serial1/0/0
     fe1 unframed
     link-protocol ppp
     ppp mp mp-group 0/0/1
    #
    interface Serial2/0/0
     fe1 unframed
     link-protocol ppp
     ppp mp mp-group 0/0/1
    #
    return
Translation
Download
Updated: 2019-03-06

Document ID: EDOC1100069331

Views: 21190

Downloads: 95

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next