No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - Interface Management

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples of the interfaces supported by the device.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a T1-F Interface

Configuring a T1-F Interface

To use a low-rate (512 kbit/s for example) T1 channel to transmit services, configure a T1-F interface to work in framed mode.

Pre-configuration Tasks

Before configuring a T1-F interface, complete the following task:

  • Install a 1E1T1-F/2E1T1-F interface card on the router and ensuring that it is registered successfully.

Context

T1-F interfaces on both ends must be configured with the same parameters except for the clock mode. Otherwise, devices on both ends cannot communicate properly.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Configure the 1E1T1-F/2E1T1-F interface card to work in T1-F mode.

    1. Run display device

      Information about the 1E1T1-F/2E1T1-F interface card is displayed. You can check the slot ID of the interface card, whether the interface card is installed in the slot, and whether it is working properly.

    2. Run display workmode { slot slot-id | all }

      The working mode of the 1E1T1-F/2E1T1-F interface card is displayed.

    3. Run set workmode slot slot-id e1t1-f t1-f

      The 1E1T1-F/2E1T1-F interface card is configured to work in T1-F mode.

      By default, a 1E1T1-F/2E1T1-F interface card works in E1-F mode.

      After completing this step, reset the 1E1T1-F/2E1T1-F interface card and wait for a while for the configuration to take effect.

      NOTE:

      The 4E1T1-F/8E1T1-F interface card only works in E1-F mode and does not support working mode switching.

  3. Run interface serial interface-number

    The T1-F interface view is displayed.

  4. Run ft1 timeslot-list list [ speed { 56k | 64k } ]

    The timeslots to be bundled and timeslot rate are specified.

    By default, all the 24 timeslots of a T1-F interface are bundled to form a channel, and the timeslot rate is 64 kbit/s. That is, the default T1-F interface rate is 1536 kbit/s.

  5. Configure other parameters on the T1-F interface.

    • Run ft1 cable { long { -7.5db | -15db | -22.5db } | short { 133ft | 266ft | 399ft | 533ft | 655ft } }ft1 clock { master | slave | system }crc { 16 | 32 | none }ft1 alarm-threshold { ais { level-1 | level-2 } | lfa { level-1 | level-2 | level-3 | level-4 } | los { pulse-detection value | pulse-recovery value } }ft1 idlecode { 7e | ff }ft1 frame-format { esf | sf }ft1 itf { number number | type { 7e | ff } }ft1 data-coding { inverted | normal }ft1 detect-rai

      description text

      The interface description is configured.

    • Run

      The transmission line attenuation is set.

      The default attenuation of the transmission line on a T1-F interface is -7.5 dB.

    • Run

      The clock mode is set.

      By default, a T1-F interface works in slave clock mode and uses line clock signals from the master clock. When T1-F interfaces of two devices are directly connected, one T1-F interface must work in master clock mode and the other in slave clock mode.

    • Run

      The CRC mode is set.

      By default, a T1-F interface uses 16-bit CRC.

    • Run

      Alarm thresholds are set.

      The default alarm thresholds are as follows:
      • Alarm indication signal (AIS) alarm: level-1.
      • Loss of frame alignment (LFA) alarm: level-1.
      • Loss of Signal (LOS) alarm: The value of pulse-detection is 176 and the value of pulse-recovery is 22, indicating that a LOS alarm is generated if less than 22 pulses are detected within 176 pulse intervals.
    • Run

      The line idle code is set.

      By default, a T1-F interface uses the line idle code 0x7e.

    • Run

      The frame format is configured.

      By default, a T1-F interface uses the extended super frame (ESF) format.

    • Run

      The interframe filling tag and the number of interframe filling tags are set.

      By default, a T1-F interface uses the interframe filling tag 0x7e and sends four filling tags between two frames.

    • Run

      Data inversion is enabled or disabled.

      By default, a T1-F interface does not invert data.

    • Run

      RAI detection is enabled.

      By default, RAI detection is enabled on a T1-F interface.

Verifying the Configuration

  • Run the display ft1 serial interface-number command to check the configuration and alarm information about the T1-F interface.
  • Run the display interface serial interface-number command to check the status and traffic statistics of the T1-F interface.
Translation
Download
Updated: 2019-03-06

Document ID: EDOC1100069331

Views: 21085

Downloads: 93

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next