No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Multicast

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples of the interfaces supported by the device.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adjusting Control Parameters for Prune Messages

Adjusting Control Parameters for Prune Messages

Context

A multicast device sends Prune messages upstream for requiring to stop forwarding multicast data. You can configure control parameters for Prune messages as required. If there is no special requirement, the default values are recommended.

Configuration Procedure

You can configure time parameters for Join/Prune messages, information carrying capacity of Join/Prune messages, and Prune delay in any sequence as required.

Adjusting Time Parameters for Join/Prune Messages

Context

A PIM device sends Prune messages to its upstream neighbor to request the neighbor to stop sending multicast data to it. Prune messages are encapsulated in a Join/Prune message, which is defined by the IPv6 PIM protocol to control multicast forwarding. When the upstream neighbor receives a Join/Prune message, it starts a timer and sets the timer value to the holdtime of the Join/Prune message. If the upstream neighbor does not receive any Join/Prune message when the timer expires, the upstream neighbor starts to forward multicast data to the downstream interface again.

NOTE:

The holdtime of Join/Prune messages can be configured in the PIM-IPv6 view or interface view. If the holdtime is configured both in the PIM-IPv6 view and interface view, the configuration in the interface view takes effect.

Default Settings

Table 5-5 lists the default settings of time parameters for Join/Prune messages.

Table 5-5  Default settings of time parameters for Join/Prune messages
Parameter Default Setting

Holdtime of Join/Prune messages

210s

Procedure

  • Global configuration
    1. Run system-view

      The system view is displayed.

    2. Run pim-ipv6

      The PIM-IPv6 view is displayed.

    3. Run holdtime join-prune interval

      The holdtime of Join/Prune messages is configured.

  • Configuration on an interface
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. Run pim ipv6 holdtime join-prune interval

      The holdtime of Join/Prune messages is configured.

Adjusting the Information Carrying Capacity of Join/Prune Messages

Context

You can configure the maximum size of each Join/Prune message, maximum number of entries in a Join/Prune message, and Join/Prune message transmission method on the router to adjust prune information sent to upstream interfaces.

  • If a PIM neighbor has a low performance and spends a long time to process each Join/Prune message, set a smaller size for each Join/Prune message on the router to reduce the number of (S, G) entries carried in Join/Prune messages. This mitigates the pressure on the PIM neighbor.
  • If the throughput of Join/Prune messages on the PIM neighbor is low, the neighbor may fail to process Join/Prune messages in a timely manner, causing route flapping. To prevent this problem, set a smaller queue size for periodically sending Join/Prune messages to reduce the number of (S, G) entries carried in Join/Prune message sent to the PIM neighbor every second. Then the router sends Join/Prune messages in many batches to the PIM neighbor, with a few Join/Prune messages in each batch.
  • By default, Join/Prune messages are transmitted to upstream neighbors in a package to improve the transmission efficiency. You can disable the package function as required.
Default Settings

Table 5-6 lists the default settings of Join/Prune messages.

Table 5-6  Default settings of Join/Prune messages
Parameter Default Setting

Maximum size of each Join/Prune message

8100 bytes

Maximum number of entries contained in Join/Prune messages

1020

Join/Prune message transmission method

Encapsulated in a package

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run pim-ipv6

    The PIM-IPv6 view is displayed.

  3. Run join-prune max-packet-length packet-length

    The maximum size of each Join/Prune message to be sent is configured.

  4. Run join-prune periodic-messages queue-size queue-size

    The maximum number of entries in Join/Prune messages sent in a second is configured.

  5. Run join-prune triggered-message-cache disable

    The function to package Join/Prune messages in real time is disabled.

Adjusting Control Parameters for Prune Delay

Context

LAN-delay specifies the delay from the time a device receives a Prune message from a downstream interface to the time it sends the Prune message to an upstream interface. A PIM device does not prune the corresponding downstream interface immediately after it sends the Prune message. If another device still requests multicast data, it needs to send a Join message to the upstream device within this period. The period for overriding the Prune message is called override-interval. The delay from the time a PIM device receives a Prune message to the time it performs the prune action is the sum of the LAN-delay and override-interval.

NOTE:

The LAN-delay and override-interval can be configured globally or on an interface. If you configure the LAN-delay and override-interval in the global PIM-IPv6 view and in the interface view simultaneously, the configuration in the interface view takes effect.

Default Settings

Table 5-7 lists the default settings of control parameters for prune delay.

Table 5-7  Default settings of control parameters for prune delay
Parameter Default Setting

LAN-delay

500 ms

Override-interval

2500 ms

Procedure

  • Global configuration
    1. Run system-view

      The system view is displayed.

    2. Run pim-ipv6

      The PIM-IPv6 view is displayed.

    3. Run hello-option lan-delay interval

      The delay for transmitting messages in a LAN is configured.

    4. Run hello-option override-interval interval

      The interval for overriding the prune action is configured.

  • Configuration on an interface
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. Run pim ipv6 hello-option lan-delay interval

      The delay for transmitting messages in a LAN is configured.

    4. Run pim ipv6 hello-option override-interval interval

      The interval for overriding the prune action is configured.

Verifying the Configuration of Control Parameters for Prune Messages

Context

After control parameters for Prune messages are configured, you can check information about the IPv6 PIM interface, statistics about IPv6 PIM control messages, and IPv6 PIM routing table.

Procedure

  • Run the display pim ipv6 interface [ interface-type interface-number | up | down ] [ verbose ] command to check IPv6 PIM information on an interface.
  • Run the display pim ipv6 control-message counters [ message-type { assert | graft | graft-ack | hello | join-prune | state-refresh | bsr } | interface interface-type interface-number ] * command to check the number of sent or received IPv6 PIM control messages.
  • Run the following commands to check the IPv6 PIM routing table.

    • Run the display pim ipv6 routing-table [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | flags flag-value | fsm | incoming-interface { interface-type interface-number | register } | mode { dm | sm | ssm } | outgoing-interface { exclude | include | match } { interface-type interface-number | none | register } ] * [ outgoing-interface-number [ number ] ] command to check detailed information about the IPv6 PIM routing table.

    • Run the display pim ipv6 routing-table brief [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | incoming-interface { interface-type interface-number | register } ] * command to check brief information about the IPv6 PIM routing table.

Translation
Download
Updated: 2019-03-06

Document ID: EDOC1100069332

Views: 21636

Downloads: 59

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next