No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Multicast

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples of the interfaces supported by the device.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Configuring the MLD Snooping Querier

(Optional) Configuring the MLD Snooping Querier

Context

When Multicast Listener Discovery (MLD) snooping is enabled on a Layer 2 device, the Layer 2 device can listen on MLD protocol packets exchanged between an MLD querier and user hosts to dynamically create Layer 2 multicast forwarding entries and provide Layer 2 multicast functions.

A Layer 2 device cannot create Layer 2 multicast forwarding entries by listening on MLD protocol packets in the following conditions, even when MLD snooping is enabled on the device:

  • The interfaces on the upstream Layer 3 multicast device have static multicast groups configured and do not run the MLD protocol.

  • The multicast source is located on the same Layer 2 network as user hosts, and therefore no Layer 3 multicast device is required.

In either of the preceding conditions, you can configure the MLD snooping querier on the Layer 2 multicast device. Then the Layer 2 multicast device substitutes for a Layer 3 multicast device to send MLD Query messages to user hosts.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run vlan vlan-id

    The VLAN view is displayed.

  3. Run mld-snooping querier enable

    The MLD snooping querier is enabled.

    NOTE:
    • After MLD snooping querier is enabled, the router periodically broadcasts MLD Query messages to all the interfaces in a VLAN, including the router ports. This may result in MLD querier reelection if an MLD querier already exists on the multicast network. If an MLD querier already exists on the multicast network, configuring MLD snooping querier is not recommended. If MLD snooping querier needs to be configured in this condition, ensure that the router has a larger IP address than the upstream MLD querier.

  4. (Optional) Set the querier parameters.

    NOTE:

    Ensure that the interval for sending MLD General Query messages is longer than the maximum response time for MLD Query messages.

    Querier Parameter

    Configuration Command

    Description

    Default Setting

    Version

    Interval for sending MLD General Query messages

    mld-snooping query-interval query-interval

    The querier sends MLD General Query messages at the specified interval to maintain memberships in a VLAN.

    60 seconds

    MLDv1, MLDv2

    MLD robustness variable

    mld-snooping robust-count robust-count

    The robustness variable defines the following values:
    • Number of times the querier sends General Query messages after startup. The packet sending interval is 1/4 of the configured interval for sending General Query messages.
    • Number of times the querier sends Group-Specific Query messages after receiving a Done message. The packet sending interval is the same as the configured interval for sending Group-Specific Query messages.

    2

    MLDv1, MLDv2

    Maximum response time for MLD Query messages

    mld-snooping max-response-time max-response-time

    After receiving an MLD Report message, the router sets the aging time of member port to: Interval for sending General-Query messages x MLD robustness variable + Maximum response time.

    After a multicast member receives an MLD Query message, it must send a Report message within the maximum response time.

    10 seconds

    MLDv2

    Interval for sending Last Member Query messages

    mld-snooping last-listener-query-interval query-interval

    When receiving a Done message from a user host, the router sets the aging time of member port to: Interval for sending Group-Specific messages x MLD robustness variable. That is, the router continuously sends Group-Specific messages for "MLD robustness variable" times. This parameter specifies the interval for sending Last Member Query messages.

    1 second

    MLDv2

  5. (Optional) Run quit

    Return to the system view.

  6. (Optional) Run mld-snooping send-query source-address ipv6-address

    The source IPv6 address of the MLD General Query message is configured.

    By default, the source IPv6 address of MLD General Query messages on an MLD querier is FE80::. If the specified address is being used by another device on the network, run this command to change the source IPv6 address.

Translation
Download
Updated: 2019-03-06

Document ID: EDOC1100069332

Views: 17642

Downloads: 42

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next