No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Multicast

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples of the interfaces supported by the device.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adjusting Assert Control Parameters

Adjusting Assert Control Parameters

Pre-configuration Tasks

Before configuring assert control parameters, complete the following task:

Configuring Basic IPv6 PIM-DM Functions

Context

When multiple PIM devices on a network segment pass the reverse path forwarding (RPF) check and forward multicast data to this network segment, assert election is required. When a device receives multicast data through a downstream interface, the device knows that other upstream devices exist on this network segment. The device then sends an Assert message to participate in the election of the unique upstream device.

PIM devices that fail the assert election disable their downstream interfaces from forwarding multicast data to this network segment. The assert loser state lasts for a period, which is called the holdtime of Assert messages. After the assert state timer times out, the devices that lost the Assert election restore pruned interfaces to the forwarding state to trigger a new round of Assert election.

NOTE:

The holdtime of Assert messages can be configured globally or on an interface. If you configure the holdtime of Assert messages in the global PIM-IPv6 view and in the interface view simultaneously, the configuration in the interface view takes effect.

Default Settings

Table 5-9 lists the default settings of assert control parameters.

Table 5-9  Default settings of assert control parameters
Parameter Default Setting

Period for holding the Assert state

180s

Procedure

  • Global configuration
    1. Run system-view

      The system view is displayed.

    2. Run pim-ipv6

      The PIM-IPv6 view is displayed.

    3. Run holdtime assert interval

      The holdtime of Assert messages is configured.

  • Configuration on an interface
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The interface view is displayed.

    3. Run pim ipv6 holdtime assert interval

      The period for holding the Assert state is configured.

Verifying the Configuration

After assert control parameters are configured, you can check information about the IPv6 PIM interface, IPv6 PIM neighbor, and IPv6 PIM routing table using the following commands:

  • Run the display pim ipv6 interface [ interface-type interface-number | up | down ] [ verbose ] command to check IPv6 PIM information on an interface.

  • Run the display pim ipv6 control-message counters [ message-type { assert | graft | graft-ack | hello | join-prune | state-refresh | bsr } | interface interface-type interface-number ] * command to check information about IPv6 PIM neighbors.

  • Run the following commands to check the IPv6 PIM routing table:

    • Run the display pim ipv6 routing-table [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | flags flag-value | fsm | incoming-interface { interface-type interface-number | register } | mode { dm | sm | ssm } | outgoing-interface { exclude | include | match } { interface-type interface-number | none | register } ] * [ outgoing-interface-number [ number ] ] command to check detailed information about the IPv6 PIM routing table.

    • Run the display pim ipv6 routing-table brief [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | incoming-interface { interface-type interface-number | register } ] * command to check brief information about the IPv6 PIM routing table.

Translation
Download
Updated: 2019-03-06

Document ID: EDOC1100069332

Views: 17704

Downloads: 42

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next