No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


CLI-based Configuration Guide - Network Management and Monitoring

AR100, AR120, AR160, AR1200, AR2200, AR3200, and AR3600 V300R003

This document provides the basic concepts, configuration procedures, and configuration examples in different application scenarios of the network management feature supported by the device.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Basic Concepts

Basic Concepts

IP FPM Model

The IP Flow Performance Measurement (FPM) model describes how service flows are measured to obtain the packet loss rate and delay. In statistical terms, the statistical objects are the service flows, and the statistical calculations determine the packet loss rate and delay of the service flows traveling across the transit network. Service flow statistical analysis is performed on the ingress and egress of the transit network.

The IP FPM model is composed of three objects: target flows, the transit network, and the statistical system. The statistical system is further classified into the Target Logical Port (TLP), Data Collecting Point (DCP), and Measurement Control Point (MCP).Figure 4-1 shows the IP FPM model.

Figure 4-1  IP FPM model

  • Target flow

    Target flows must be pre-defined.

    One or more fields in IP headers can be specified to identify target flows. The field can be the source IP address or prefix, destination IP address or prefix, protocol type, source port number, destination port number, or type of service (ToS). The more fields specified, the more accurately flows can be identified. Specifying as many fields as possible is recommended to maximize the measurement accuracy.

  • Transit network

    The transit network only bears target flows. The target flows are not generated or terminated on the transit network. The transit network can be a Layer 2 (L2), Layer 3 (L3), or L2+L3 hybrid network. Each node on the transit network must be reachable at the network layer.

  • TLP

    TLPs are interfaces on the edge nodes of the transit network. TLPs perform the following actions:
    • Compile statistics on the packet loss rate and delay.
    • Generate statistics, such as the number of packets sent and received, traffic bandwidth, and timestamp.

    An In-Point-TLP collects statistics about service flows it receives. An Out-Point-TLP collects statistics about service flows it sends.

  • DCP

    DCPs are edge nodes on the transit network. DCPs perform the following actions:
    • Manage and control TLPs.
    • Collect statistics generated by TLPs.
    • Report the statistics to an MCP.
  • MCP

    MCPs can be any nodes on the transit network. MCPs perform the following actions:
    • Collect statistics reported by DCPs.
    • Summarize and calculate the statistics.
    • Report measurement results to user terminals or the network management system (NMS).

Color Bits

The color bit is also called characteristics bit. In IP FPM, there are color bits for packet loss measurement and for delay measurement. The color bits indicate that a service packet is used for packet loss measurement or delay measurement.

Figure 4-2 shows the possible color bits in the IPv4 packet header.
Figure 4-2  IPv4 packet header format

  • The third to seventh bits in the ToS field are seldom used in actual applications. These bits, if available, can be used as color bits for service packets.

  • Bit 0 in the Flags field is reserved and can be directly used as a color bit.

If two or more bits in the IPv4 packet header have not been planned for other purposes, they can be used for packet loss and delay measurement at the same time. If only one bit in the IPv4 packet header has not been planned, it can be used for either packet loss or delay measurement in one IP FPM instance.

Updated: 2019-03-06

Document ID: EDOC1100069336

Views: 30803

Downloads: 177

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Previous Next