No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

CloudEngine 12800 and 12800E V200R005C10

This document describes the configurations of Device Management, including device status query, hardware management, Information Center Configuration, NTP, Synchronous Ethernet Configuration, Fault Management Configuration, Energy-Saving Management Configuration, Performance Management Configuration, Maintenance Assistant Configuration, and OPS Configuration.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring a Clock Source

Configuring a Clock Source

Context

To implement clock synchronization on a switch, configure a clock source first. The switch supports building integrated timing supply (BITS), Precision Time Protocol (PTP) and line clock sources. The configuration varies depending on the clock source. Follow one of the following procedures based on the clock source used in your network.

Pre-configuration Tasks

Before configuring a clock source, complete the following tasks:
  • Connect devices that require clock synchronization over the Ethernet using clock cables or Ethernet interfaces to establish a clock synchronization network.
  • Connect the clock source to the clock synchronization network using a clock cable or an Ethernet interface.

Procedure

  • Configure a BITS clock source.
    1. Run system-view

      The system view is displayed.

    2. Run clock bits-type [ chassis chassis-id ] bits0 { 2mhz | 2mbps } [ slot slot-id ]

      A signal type is configured for the BITS clock source.

      By default, the signal type for BITS0 clock source is 2mbps.

    3. Run clock source [ chassis chassis-id ] bits0 synchronization enable [ slot slot-id ]

      Clock synchronization is enabled for the BITS clock source.

      By default, clock synchronization is disabled for a BITS clock source.

    4. Run clock source [ chassis chassis-id ] bits0 priority priority-value [ slot slot-id ]

      A priority is configured for the BITS clock source.

      By default, a BITS clock source does not have a priority, indicating that it cannot participate in clock source selection. A smaller priority value indicates a higher priority.

    5. (Optional) Determine the SSM quality level based on the clock signal type.

      • If the clock signal type is 2mbps, run clock sa-bit { sa4 | sa5 | sa6 | sa7 | sa8 } source [ chassis chassis-id ] bits0 [ slot slot-id ]

        The BITS clock source is configured to obtain an SSM quality level from a specified timeslot of clock signals.

        By default, a BITS clock source obtains an SSM quality level from timeslot sa4 of clock signals.

      • If the clock signal type is 2mhz, run clock source [ chassis chassis-id ] bits0 ssm { dnu | prc | sec | ssua | ssub | unk } [ slot slot-id ]

        An SSM quality level is configured for the BITS clock source.

        By default, no SSM quality level is configured for a BITS clock source.

    6. Run commit

      The configuration is committed.

  • Configure a PTP clock source.
    1. Run system-view

      The system view is displayed.

    2. Run clock source ptp synchronization enable

      Clock synchronization is enabled for the PTP clock source.

      By default, clock synchronization is disabled for a PTP clock source.

    3. Run clock source ptp priority priority-value

      A priority is configured for the PTP clock source.

      By default, a PTP clock source does not have a priority, indicating that it cannot participate in clock source selection. A smaller priority value indicates a higher priority.

    4. (Optional) Run clock source ptp ssm { dnu | prc | sec | ssua | ssub | unk }

      An SSM quality level is set for the PTP clock source.

      By default, no SSM quality level is set for a PTP clock source.

    5. Run commit

      The configuration is committed.

  • Configure a line clock source.
    1. Run system-view

      The system view is displayed.

    2. Run interface interface-type interface-number

      The view of the interface connected to the line clock source is displayed.

    3. Run clock synchronization enable

      Clock synchronization is enabled for the line clock source.

      By default, clock synchronization is disabled for a line clock source.

    4. (Optional) Run clock [ 2msync-1 | 2msync-2 ] priority priority-value

      A priority is configured for the line clock source.

      By default, a line clock source does not have a priority, indicating that it cannot participate in clock source selection. A smaller priority value indicates a higher priority.

    5. (Optional) Run clock ssm { dnu | prc | sec | ssua | ssub | unk }

      An SSM quality level is set for the line clock source.

      By default, the SSM quality level of a line clock source is sent from the remote device.

    6. Run commit

      The configuration is committed.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074722

Views: 15606

Downloads: 18

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next