No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Multicast

CloudEngine 12800 and 12800E V200R005C10

This document describes the configurations of IP multicast, including IP multicast basics, IGMP, MLD, PIM (IPv4), PIM (IPv6), MSDP, multicast VPN, multicast route management (IPv4), multicast route management (IPv6), IGMP snooping, MLD snooping, static multicast MAC address, multicast VLAN, multicast network management.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Multicast Load Splitting

Multicast Load Splitting

Load splitting is different from load balancing. Load splitting provides a way to distribute data streams destined for the same destination to multiple equal-cost paths, which may not result in a balanced traffic load on the paths. Load balancing is a special form of load splitting and distributes even data traffic loads on multiple equal-cost paths.

Implementation

By default, if multiple equal-cost optimal routes are available, a router selects the route with the largest next-hop address from the IGP routing table according to the RPF check policy.

Multicast load splitting enables a router to distribute multicast traffic to multiple equal-cost routes, instead of selecting only one route based on the RPF check policy.

In Figure 9-3, the multicast source (Source) sends multicast streams to group G. RouterA and RouterD run an Interior Gateway Protocol (IGP), such as OSPF, to implement IP interworking. Two equal-cost paths are available: RouterA → RouterB → RouterD and RouterA → RouterC → RouterD. Based on the default RPF check policy, multicast streams are forwarded through interface Int1 of RouterA because Int1 has a larger IP address than Int0. After multicast load splitting is configured on RouterA, RouterA does not select forwarding paths by comparing the next-hop IP addresses. Instead, multicast streams are forwarded along both of the two equal-cost paths.
Figure 9-3 Multicast forwarding without and with multicast load splitting

Multicast Load Splitting Modes

Various methods are available to split (*, G) and (S, G) data streams in different scenarios.

  • Load splitting by group address

    In Figure 9-4, the source sends data streams to different multicast groups (G1 to G10). Router7, Router6, and Router5 each have two equal-cost paths to the source. These routers use route selection algorithms to select an optimal path for data sent to each group. In this load splitting mode, streams transmitted on different paths are sent to different groups.

    Figure 9-4 Load splitting by group address
  • Load splitting by source address

    In Figure 9-5, different sources (S1 to S10) send data streams to the same group. Router7, Router6, and Router5 each have two equal-cost paths to the sources. These routers use route selection algorithms to select an optimal path for data from each source. In this load splitting mode, streams transmitted on different paths are sent from different sources.

    Figure 9-5 Load splitting by source address
  • Load splitting based on source and group addresses

    In Figure 9-6, different sources (S1 to S10) send data streams to different groups (G1 to G10). Router7, Router6, and Router5 each have two equal-cost paths to the sources. These routers use route selection algorithms to select an optimal path for each (S, G) stream. In this load splitting mode, streams transmitted on different paths have different source and group addresses.

    Figure 9-6 Load splitting based on source and group addresses
  • Other load splitting methods

    Figure 9-7 Load splitting network

    The following load balancing methods can also be used on the network shown in Figure 9-7.

    • Stable-preferred load splitting

      When route flapping occurs on a multicast network, frequent changes of multicast traffic distribution on equal-cost paths will cause the route flapping to become worse. Stable-preferred load splitting can be configured to solve this problem. When route flapping occurs, a router with stable-preferred load splitting adjusts traffic distribution on equal-cost paths until route flapping ends. When the network topology becomes stable, the router evenly distributes (S, G) streams from the same source to equal-cost paths.

    • Load splitting based on link bandwidth

      Transmission paths have different capabilities. If routing entries are evenly distributed on the equal-cost paths, the bandwidth of each path cannot be fully leveraged. After this load splitting mode is configured, routing entries can be distributed on paths based on link bandwidth.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074724

Views: 38912

Downloads: 13

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next