No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document provides the explanations, causes, and recommended actions of alarms on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
OSPFV3_1.3.6.1.4.1.2011.5.25.147.0.16 hwOspfv3PeerFlappingSuppressStatusChange

OSPFV3_1.3.6.1.4.1.2011.5.25.147.0.16 hwOspfv3PeerFlappingSuppressStatusChange

Description

The status of peer flapping suppress is changed.(ProcessId=[ProcessId], RouterId=[RouterId], AreaId=[AreaId], ifName=[ifName], SuppressStatus=[SuppressStatus], SuppressReason=[SuppressReason])

The status of OSPFv3 neighbor relationship flapping suppression changed.

Attributes

Attribute

Description

Alarm or Event

Event

Trap Severity

Informational

Mnemonic Code

hwOspfv3PeerFlappingSuppressStatusChange

Trap OID

1.3.6.1.4.1.2011.5.25.147.0.16

Alarm ID

This is an event trap and does not involve alarm ID.

Alarm Type

This is an event trap and does not involve alarm type.

Raise or Clear

This is an event trap and does not involve alarm generation or clearance.

Match trap

This is an event trap and does not involve the matching trap.

Parameters

Parameter

Description

ProcessId

Process ID

RouterId

Router ID

AreaId

Area ID

ifName

Interface name

SuppressStatus

Suppression status

SuppressReason

Suppression causes are as follows:

  • 1: The interval between two successive neighbor status changes from Full to a non-Full state was longer than the resume interval.
  • 2: A configuration was changed. For example, the OSPFv3 process was reset.
  • 3: An interface was forced to exit from OSPFv3 neighbor relationship flapping suppression using the reset ospfv3 suppress-flapping peer command.
  • 4: The OSPFv3 neighbor relationship flapped frequently.
  • 5: OSPFv3 neighbor relationship flapping suppression exited from Hold-down mode and began to work in Hold-max-cost mode.

VB Parameters

VB OID

VB Name

VB Index

1.3.6.1.4.1.2011.5.25.147.1.12.7

hwOspfv3ProcessId

N/A

1.3.6.1.4.1.2011.6.125.1.11.4

hwOspfv3RouterId

N/A

1.3.6.1.4.1.2011.5.25.147.1.12.7

hwOspfv3AreaIdIndex

N/A

1.3.6.1.4.1.2011.5.25.147.1.12.4

hwOspfv3IfName

N/A

1.3.6.1.4.1.2011.5.25.147.1.12.10

hwOspfv3PeerFlappingSuppressStatus

N/A

1.3.6.1.4.1.2011.5.25.147.1.12.11

hwOspfv3PeerFlappingSuppressInterval

N/A

Impact on the System

Services may be interrupted if OSPFv3 neighbor relationship flapping suppression persists on the interface.

Possible Causes

OSPFv3 neighbor relationship flapping suppression started, or the interface exited from the suppression.

Procedure

  1. Check whether frequent interface flapping occurs.

    • If frequent interface flapping occurs, this trap message is informational only and no action is required.
    • If no frequent interface flapping occurs, go to Step 2.

  2. Run the reset ospfv3 process-id suppress-flapping peer [ interface-type interface-number ] [ notify-peer ] command to force the interface to exit from OSPFv3 neighbor relationship flapping suppression.
  3. End.
Translation
Download
Updated: 2019-04-02

Document ID: EDOC1100074754

Views: 17742

Downloads: 25

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next