No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of IP Unicast Routing, including IP Routing, Static Route, RIP, RIPng, OSPF, OSPFv3, IPv4 IS-IS, IPv6 IS-IS, BGP, Routing Policy, and PBR.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring RIP-2 Route Summarization

Configuring RIP-2 Route Summarization

Context

A large RIP network must maintain large RIP routing tables, which occupy a lot of memory on devices. Transmitting and processing the routing information requires many network resources. Route summarization can reduce the routing table size and minimize impact of route flapping on network.

RIP supports automatic summarization and manual summarization. Manual summarization takes precedence over automatic summarization. To advertise all subnet routes, disable automatic route summarization of RIP-2.

NOTE:

By default, if split horizon or poison reverse has been configured, classful route summarization is invalid. When summarized routes are sent to the natural network border, split horizon or poison reverse must be disabled.

Procedure

  • Configure automatic route summarization of RIP-2.
    1. Run the system-view command to enter the system view.
    2. Run the rip [ process-id ] command to enter the RIP view.
    3. Run the version 2 command to set the RIP version to RIP-2.
    4. Run the summary command to enable automatic route summarization.
    5. (Optional) Run the summary always command to enable automatic route summarization. This command can enable automatic summarization of RIP-2 no matter whether split horizon and poison reverse are enabled.

      NOTE:

      The summary command is used in the RIP view to enable classful network-based route summarization of RIP-2.

    6. Run commit

      The configuration is committed.

  • Configure manual route summarization of RIP-2.
    1. Run the system-view command to enter the system view.
    2. Run the interface interface-type interface-number command to enter the interface view.
    3. On an Ethernet interface, run undo portswitch

      The interface is switched to Layer 3 mode.

      By default, an Ethernet interface works in Layer 2 mode.

      The mode switching function takes effect when the interface only has attribute configurations (for example, shutdown and description configurations). Alternatively, if configuration information supported by both Layer 2 and Layer 3 interfaces exists (for example, mode lacp and lacp system-id configurations), no configuration that is not supported after the working mode of the interface is switched can exist. If unsupported configurations exist on the interface, delete the configurations first and then run the undo portswitch command.

      NOTE:

      If many Ethernet interfaces need to be switched to Layer 3 mode, run the undo portswitch batch interface-type { interface-number1 [ to interface-number2 ] } &<1-10> command in the system view to switch these interfaces to Layer 3 mode in batches.

    4. Run the rip summary-address ip-address mask [ avoid-feedback ] command to configure RIP-2 to advertise the local summarization IP address.

      NOTE:

      The rip summary-address ip-address mask [ avoid-feedback ] command is run in the interface view to enable classless network-based route summarization of RIP-2.

    5. Run commit

      The configuration is committed.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074760

Views: 58620

Downloads: 63

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next