No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of IP Unicast Routing, including IP Routing, Static Route, RIP, RIPng, OSPF, OSPFv3, IPv4 IS-IS, IPv6 IS-IS, BGP, Routing Policy, and PBR.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
NQA for Static Routes

NQA for Static Routes

As mentioned previously, static routes do not have a dedicated fault detection mechanism. If a fault occurs on a non-directly connected link, the corresponding static route will not be automatically deleted from the IP routing table. This cannot ensure in-time link switchover and can interrupt services for a significant amount of time. The network administrator must delete the corresponding static route to allow traffic to switch to an available link.

An effective method is required to detect faults in links related to static routes. BFD for static routes is applicable only to the scenario where both communicating devices support BFD. If either of the two communicating devices supports NQA, NQA for static routes can be used to detect link faults.

NQA for static routes refers to the association between a static route and an NQA test instance. The system can use the NQA test instance to check the link status and determines an optimal route in time according to the NQA test result to prevent communication interruption and ensure service quality. NQA for static routes functions as follows:
  • If the NQA test instance detects a link fault, the system sets the static route to inactive. The route becomes unavailable and is deleted from the IP routing table.
  • If the NQA test instance finds that the link recovers, the system sets the static route to active. The route becomes available and is added to the IP routing table.

For details about NQA, see "NQA Configuration - Principles" in the Configuration Guide - Network Management and Monitoring.

NOTE:

When a static route is associated with an NQA test instance, only ICMP test instances are used to test whether there are reachable routes between the source and destination.

Each static route can be associated with only one NQA test instance.

Application Scenario

On the network shown in Figure 2-1, each access switch provides access services for 10 users, and a total of 100 users are connected to the network. Because dynamic routing protocols are unavailable for communication between RouterB and users, static routes destined for users are configured on RouterB. For network stability, RouterC, functioning as the backup for RouterB, is configured with static routes to the same destination. RouterA, RouterB, and RouterC run a dynamic routing protocol to learn routes from each other. RouterB and RouterC import static routes using a dynamic routing protocol and have different costs for these static routes. After the configuration is complete, RouterA can use the dynamic routing protocol to learn routes destined for users from RouterB and RouterC. RouterA uses the link related to the static route with a lower cost as the active link and the other link as the standby link.

NQA for static routes is configured on RouterB. NQA tests are performed to check the active link of RouterB → SwitchA → SwitchC (SwitchD). If the active link fails, the corresponding static route is deleted from the routing table, and traffic diverts to the standby link of RouterC → SwitchB → SwitchC (SwitchD). If both links work properly, traffic travels along the active link.

Figure 2-1 Networking diagram for applying NQA for static routes

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074760

Views: 45732

Downloads: 58

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next