No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - IP Unicast Routing

CloudEngine 8800, 7800, 6800, and 5800 V200R005C10

This document describes the configurations of IP Unicast Routing, including IP Routing, Static Route, RIP, RIPng, OSPF, OSPFv3, IPv4 IS-IS, IPv6 IS-IS, BGP, Routing Policy, and PBR.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Associating IPv4 Static Routes with NQA

(Optional) Associating IPv4 Static Routes with NQA

Pre-configuration Tasks

Before associating IPv4 static routes with NQA, complete the following task:

  • Configure link layer parameters for interfaces to ensure that the link layer protocol on the interfaces is Up.

Procedure

  1. Configure an ICMP NQA test instance.
    1. Run system-view

      The system view is displayed.

    2. Run nqa test-instance admin-name test-name

      An NQA test instance is created, and the view of the test instance is displayed.

    3. Run test-type icmp

      The test type is set to ICMP.

      NOTE:

      When a static route is associated with an NQA test instance, only ICMP test instances are used to test whether there are reachable routes between the source and destination.

    4. Run destination-address ipv4 ip-address

      The destination address is set.

      In an NQA test instance, you can specify an NQA server by running the destination-address command to configure a destination address for the NQA test instance.

    5. (Optional) Run frequency interval

      The interval for automatically performing an NQA test is set.

      By default, no interval is set, that is, only one test is performed.

    6. (Optional) Run probe-count number

      The number of probes to be sent each time is set for the NQA test instance.

      By default, the number of probes is 3.

      By sending probes multiple times in an NQA test instance, you can accurately estimate network quality based on the collected statistics.

    7. Run start

      The NQA test instance is started.

      The start command can configure an NQA test instance to be started immediately, at a specified time, after a specified delay, or every day. You can perform one of the following operations as required:
      • Run start now [ end { at [ yyyy/mm/dd ] hh:mm:ss | delay { seconds second | hh:mm:ss } | lifetime { seconds second | hh:mm:ss } } ]

        The NQA test instance is started immediately.

      • Run start at [ yyyy/mm/dd ] hh:mm:ss [ end { at [ yyyy/mm/dd ] hh:mm:ss | delay { seconds second | hh:mm:ss } | lifetime { seconds second | hh:mm:ss } } ]

        The NQA test instance is started at a specified time.

      • Run start delay { seconds second | hh:mm:ss } [ end { at [ yyyy/mm/dd ] hh:mm:ss | delay { seconds second | hh:mm:ss } | lifetime { seconds second | hh:mm:ss } } ]

        The NQA test instance is started after a specified delay.

      • Run start daily hh:mm:ss to hh:mm:ss [ begin { yyyy-mm-dd | yyyy/mm/dd } ] [ end { yyyy-mm-dd | yyyy/mm/dd } ]

        The NQA test instance is started every day.

    8. Run commit

      The configuration is committed.

    9. Run quit

      Return to the system view.

  2. Associate static routes with an NQA test instance.
    1. Run ip route-static ip-address { mask | mask-length } { nexthop-address | interface-type interface-number [ nexthop-address ] } [ preference preference | tag tag ] * track nqa admin-name test-name [ description text ]

      IPv4 static routes are associated with an NQA test instance.

      NOTE:

      The destination address of an NQA test instance cannot be the destination address of an associated static route.

      If the static route associated with an NQA test instance is associated with another NQA test instance, the static route is disassociated from the first NQA test instance.

    2. Run commit

      The configuration is committed.

Verifying the Configuration

After IPv4 static routes are associated with NAQ, run the following commands to verify the configuration.

  • Run the display current-configuration | include nqa command to check the configuration of association between static routes and NQA.

  • Run the display nqa results [ collection ] [ test-instance admin-name test-name ] command to check the NQA test result.

    The NQA test result cannot be displayed automatically. You must run the display nqa results command to view the NQA test result. By default, the command output shows the results of the latest five NQA tests.

Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100074760

Views: 49146

Downloads: 58

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next